Alkene Based Monolayer Films as Anti-stiction Coatings for Polysilicon Mems

نویسندگان

  • W. Robert Ashurst
  • Christina Yau
  • Carlo Carraro
  • Roger T. Howe
  • Roya Maboudian
چکیده

This paper describes a new class of anti-stiction coatings for silicon MEMS that is based on the free radical reaction of a primary alkene (e.g., 1-octadecene, C16H33CH=CH2) with hydrogen terminated silicon [1,2]. The new monolayer coating has several key advantages over the previously reported octadecyltrichlorosilane (OTS) and 1H,1H,2H,2Hperfluorodecyltrichlorosilane (FDTS) based self-assembled monolayers (SAMs) [3,4]: 1) The coating does not produce HCl at any stage in the monolayer formation whereas chlorosilane-based chemistry does. 2) The coating does not require the formation of an intervening oxide layer. 3) The film formation procedure for alkene-based monolayers is simpler than for chlorosilane-based SAMs for two main reasons. First, the surface oxidation step is eliminated. Second, the coating solution does not need to be conditioned before use, since water is not a reagent in this process. 4) The coating process is much more robust since it is essentially insensitive to relative humidity. 5) The coated surfaces have much fewer particulates in comparison to those coated with OTS. 6) The coating process can be made selective to coat only exposed silicon by generating radicals using a radical initiator. The coating is evaluated in several ways, including X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), contact angle analysis (CAA), work of adhesion by cantilever beam array technique and coefficient of static friction using a sidewall testing device. The octadecene film is compared to the OTS SAM with respect to anti-stiction properties. XPS data confirm the absence of oxygen in both freshly prepared samples and in samples aged for four months in laboratory ambient. Water and hexadecane contact angles, and work of adhesion data are similar to those of OTS. AFM shows that the samples which receive 1-octadecene films accumulate far fewer particles during processing than those which receive the OTS SAM treatment.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Self-assembled monolayers as anti-stiction coatings for MEMS: characteristics and recent developments

Despite significant advances in surface micromachining technology, stiction remains a key problem, severely limiting the realization Ž . and reliability of many micro-electro-mechanical systems MEMS devices. In this article, we focus on self-assembled monolayers as release and anti-stiction coatings for MEMS. Their formation mechanism, the microstructure coating process, and the characteristics...

متن کامل

The Influence of an OTS Self Assembled Monolayer on the Wear Resistant Properties of Polysilicon Based MEMS

Polysilicon MEMS structures are coated with self-assembled monolayers (SAMs) to reduce stiction and improve wear resistance. This study reports on an octadecyltrichlorosilane (OTS) coated low pressure chemical vapour deposited (LPCVD) polysilicon based MEMS test structure fabricated at Sandia National Laboratories, USA. The surface morphology and OTS layer have been studied by SEM, XPS and AFM....

متن کامل

High-cycle Fatigue in Micron-scale Structural Films of Polycrystalline Silicon: a Reaction-layer Failure Mechanism

A study has been made of high-cycle fatigue in 2-μm thick structural films of ntype, polycrystalline silicon for MEMS applications. Using an “on-chip” test structure resonating at ~40 kHz, such thin-film polysilicon is shown to display “metal-like” stress-life fatigue behavior in room air environments, with failures occurring after lives in excess of 10 cycles at stresses as low as half the fra...

متن کامل

Molecular dynamics simulations of friction between alkylsilane monolayers

Alkylsilane monolayer films are used in the fabrication of microelectromechanical systems (MEMS) as anti-stiction coatings. Recently, these films are also being considered as anti-friction coating for MEMS parts that operate under conditions of friction, such as gears, motors, etc. Study of frictional behaviour of these films is of significant interest from the performance point of view. In thi...

متن کامل

A Gas-Expanded Liquid Nanoparticle Deposition and Supercritical Drying Process to Reduce Adhesion of Microstructures

It is well established that supercritical fluids such as supercritical CO2 are dense fluids that do not demonstrate the often detrimental surface tensions and interfacial phenomena exhibited by other liquids. Supercritical CO2 has hence become widely used in the microelectromechanical systems (MEMS) industry to dry release devices while avoiding the liquid-vapor interface that can cause the cap...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2000