Cryogenic Permeability of Polyimide Shells

نویسندگان

  • James Wang
  • David Harding
چکیده

Polyimide shells are used as targets in Inertial Confinement Fusion (ICF) experiments. These shells are filled with DT gas, then cooled to low temperatures for cryogenic laser shots. During target preparation, shells require careful pressure and temperature control due to their sensitivity. The pressure is governed partly by permeation through the shell wall, which can only be determined with the knowledge of the shell permeability over a wide temperature range. A new method was developed to test the permeability of shells at temperatures ranging from 123K to 23 K. This method produced results at room temperature comparable to those using current setups. Arrhenius' relationship was observed from room temperature to 120K and the activation energy for permeation was determined for shells prepared under different processing conditions. The results will allow the permeability of shells to be predicted for various temperatures.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Fabrication of Polyimide Shells for Use as ICF Targets

LLE Review, Volume 71 113 The current target-shell material for direct-drive experiments on OMEGA is a low-density hydrocarbon polymer fabricated using a low-pressure plasma polymerization process. This material meets the immediate requirements for an inertial confinement fusion (ICF) target shell: low density; smooth surfaces (outer and inner); spherical and concentric; and the capability of b...

متن کامل

Optimizing the Fabrication of Polyimide Shells

196 LLE Review, Volume 88 Introduction Polyimide is being developed as an ablator material for inertial confinement fusion (ICF) targets because of its superior mechanical and thermal properties.1 A typical target design for the OMEGA laser system consists of a spherical shell, 1 mm in diameter and 1 μm in wall thickness, with a 100-μm-thick layer of solid deuterium and tritium (DT) uniformly d...

متن کامل

Polyimide x-ray filter substrates optimized for cryogenic temperatures

New generation x-ray instruments for spacecraft such as ASTRO-E and CONSTELLATION-X have very specialized requirements, notably operation at cryogenic temperatures. Luxel Corporation, under a NASA Phase I SBIR contract, undertook demonstrating feasibility of producing polyimide films suitable for use as x-ray filter substrates specifically optimized for cryogenic applications. 5000Å thick polyi...

متن کامل

EUROPEAN ORGANIZATION FOR NUCLEAR RESEARCH CERN - ACCELERATORS AND TECHNOLOGY SECTOR Silica–silica Polyimide Buffered Optical Fibre Irradiation and Strength Experiment at Cryogenic Temperatures for 355 nm Pulsed Lasers

A controlled UV-light delivery system is envisioned to be built in order to study the stability properties of superconducting strands. The application requires a wave guide from room temperature to cryogenic temperatures. Hydrogen loaded and unloaded polyimide buffered silica–silica 100 lm core fibres were tested at cryogenic temperatures. A thermal stress test was done at 1.9 K and at 4.2 K wh...

متن کامل

Gas Separation Properties of Mixed Matrix Membranes based on Polyimide and Graphite Oxide

In this work, three different graphene-based materials, namely graphite oxide (GrO), thermally reduced graphite oxide (T-RGrO) and ascorbic acid multi-phase reduced graphene oxide (AMP-RGO), were synthesized and used to produce mixed matrix membranes (MMM) based on Matrimid®5218 for as separation. From the samples produced, a complete set of characterization was performed including XRD, FTIR, T...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2008