IN SITU TIME-RESOLVED X-RAY DIFFRACTION OF TOBERMORITE FORMATION PROCESS UNDER HYDROTHERMAL CONDITION: INFLUENCE OF REACTIVE Al COMPOUND

نویسندگان

  • K. Matsui
  • A. Ogawa
  • J. Kikuma
  • M. Tsunashima
  • T. Ishikawa
  • S. Matsuno
چکیده

Hydrothermal formation reaction of tobermorite in the autoclaved aerated concrete (AAC) process has been investigated by in-situ X-ray diffraction. High-energy X-rays from a synchrotron radiation source in combination with a newly developed autoclave cell and a photon-counting pixel array detector were used. XRD measurements were conducted in a temperature range of 100–190 °C throughout 12 h of reaction time with a time interval of 4.25 min under a saturated steam pressure. To clarify the tobermorite formation mechanism in the AAC process, the effect of Al addition on the tobermorite formation reaction was studied. As intermediate phases, non-crystalline calcium silicate hydrate (C-S-H), hydroxylellestadite (HE), and katoite (KA) were clearly observed. Consequently, it was confirmed that there were two reaction pathways via C-S-H and KA in the tobermorite formation reaction of Al containing system. In addition, detailed information on the structural changes during the hydrothermal reaction was obtained. INTRODUCTION Autoclaved aerated concrete (AAC) is widely used as a building material because of its superior heat-insulation efficiency and fire resistance (Grutzeck, 2005). A typical process for the AAC production includes hydrothermal treatment of a mixture of quartz sand, lime, cement, gypsum, and some other additives at high temperatures (typically, 180–200 °C) under a saturated steam pressure, which results in the formation of crystalline calcium silicate hydrates, namely, tobermorite (Ca5Si6O16(OH)2-4H2O). Since both the quantity and quality of tobermorite formed in the AAC significantly affect the mechanical properties of AAC (Mitsuda et al., 1992), understanding the mechanism of tobermorite formation during the hydrothermal treatment (i.e. autoclave process) is very important in AAC production. 59 Copyright ©JCPDS-International Centre for Diffraction Data 2011 ISSN 1097-0002 60

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

IN SITU FABRICATION OF Al 2024-Mg2Si COMPOSITE BY SPARK PLASMA SINTERING OF REACTIVE MECHANICALLY ALLOYED POWDER

In situ Al2024- Mg2Si composite was fabricated by spark plasma sintering (SPS) of reactive powder. Reactive powder was obtained from mechanical alloying (MA) of elemental powders. Clad layers of in situ composite were fabricated on Al substrates by spark plasma sintering (SPS). Structural evolution during MA process and after SPS was investigated by X-ray diffractometery (XRD). Scanning electro...

متن کامل

Recent results from the in situ study of hydrothermal crystallisations using time-resolved X-ray and neutron diffraction methods.

We present new time-resolved powder diffraction data measured in situ during the hydrothermal crystallisation of two families of crystalline inorganic materials. In the first study, we have used time-resolved energy-dispersive X-ray diffraction (EDXRD) to follow the formation of zeolitic zinc phosphates from amine phosphates and zinc oxide in acidic solutions at 60-150 degrees C. The advantage ...

متن کامل

Time and position resolved in situ X-ray diffraction study of the hydrothermal conversion of gypsum monoliths to hydroxyapatite.

Time-resolved energy dispersive X-ray diffraction (EDXRD) data have been measured in situ from cast blocks of gypsum, CaSO(4) x 2 H(2)O, in the presence of reactive phosphate solutions under hydrothermal conditions (100 < or = T < or = 180 degrees C) in order to understand the formation of hydroxyapatite monoliths, for applications such as in artificial bone or dental materials. Measurement of ...

متن کامل

IN-SITU FABRICATION PROCESS OF AL- TIC COMPOSITE BY SLAG

The new in situ method for AI-TiC composite fabrication has been carried out. In this method, fabrication of AI-TiC composite by simultaneous introduction of titanium oxide and carbon into aluminum melt was investigated.. Under the process conditions, titanium and carbon reaction results in titanium carbide whiskers. The salt containing keriolite (Na3AIF6), titanium oxide (TiO2) and graphite us...

متن کامل

In-situ reactive synthesis of full dense Si2N2O by incorporating of Amourphous nanosized Si3N4;effect of MgO and Y2O3

Si2N2O is considered as a new great potential structural/functional candidate in place of Si3N4. The amorphous Si3N4 nanopowder was incorporated into silica sol by adding of MgO and Y2O3 as sintering aid. Synthesized powders were heated by spark plasma sintering at a heating rate of 100 oC/min yielded fully dense compacts at 1550 and 1750 oC for 40 min. The phase formation of samples was charac...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2011