Polymerization efficacy of simplified adhesive systems studied by NMR and MRI techniques.

نویسندگان

  • T G Nunes
  • F C P Garcia
  • R Osorio
  • R Carvalho
  • M Toledano
چکیده

OBJECTIVE To ascertain the efficacy of polymerization of self-etching dental adhesives in different solvent evaporation conditions. MATERIAL AND METHODS Four self-etching adhesive systems were studied. Two of them are classified as mild two-step self-etching adhesives (Clearfil SE Bond, Protect Bond) and the other two are strong one-step systems (Xeno III, ADP-Prompt-L-Pop). The influence of temperature and duration of the air-drying period on photo-polymerization was followed by: gravimetry, (1)H solid-state NMR spectroscopy and stray-field MRI. The evolution of proton magnetization with irradiation time was recorded and correlated with volumetric polymerization shrinkage and extent of reaction; evaporation and hardening effects were identified. RESULTS Main variables determining water-solvent evaporation of the tested adhesives are: (1) water/HEMA relative concentration, (2) presence of photoinitiator compounds in the primer (SEB) and (3) presence of ethanol (XENO). SEB shows the highest extent of photo-polymerization of the tested adhesives. The lowest volumetric contraction was obtained for APLP and XENO and the attempt to remove the solvents did not increase the extent of polymerization significantly. CONCLUSIONS Temperature increase following photo-polymerization reaction is dominant towards the effect of the drying step for solvent evaporation in self-etching systems. Attempts to remove the solvents did not increase the extent of polymerization, so other problems are impairing the polymerization of one-step adhesives. CLINICAL SIGNIFICANCE The use of tested one-step adhesives is discouraged as the attained low extent of polymerization may lead to low bond strength, high susceptibility to degradation and also will favor a continuing etching effect on the underlying dentin.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Factors contributing to the incompatibility between new adhesive systems and various composite resin restorations

  Factors contributing to the incompatibility between new adhesive systems and various composite resin restorations     Dr. F. Maleknejad* - Dr. H. Moosavi**  *- Associate Professor of Operative Dentistry Dept. - Faculty of Dentistry – Mashhad University of Medical Sciences.  **- Assistant Professor of Operative Dentistry Dept. - Faculty of Dentistry – Mashhad University of Medical Sciences.   ...

متن کامل

Dental adhesion review: aging and stability of the bonded interface.

OBJECTIVE Most of current dental adhesive systems show favorable immediate results in terms of retention and sealing of bonded interface, thereby counteracting polymerization shrinkage that affects resin-based restorative materials. Despite immediate efficacy, there are major concerns when dentin bonded interfaces are tested after aging even for short time period, i.e. 6 months. METHODS This ...

متن کامل

Comparison of Shear Bond Strength of Composite Restorations to Intact Enamel of Primary Incisors When Using Different Conditioners and Adhesive Systems

Introdouction: Esthetic demands of patients have led to the introduction of tooth-colored restorations wherecomposite resins are bonded to the enamel using acid etch techniques. Total etch adhesion systems are still considered as the gold standard among bonding systems. However, clinicians have a tendency to use adhesive systems with simpler application procedures. The aim of the present stu...

متن کامل

Microleakage assessment of one- and two-step self-etch adhesive systems with ‎the low shrinkage composites

BACKGROUND AND AIM: Different studies evaluating one-step self-etch (SE) adhesive systems show contradictory findings, so the aim of this study was to compare the microleakage of one-step SE adhesive systems and CLEARFIL SE BOND (that serves as the “gold-standard” SE adhesive) with low shrinkage composites. METHODS: In this in vitro study, Class V cavities with the occlusal margin in enamel and...

متن کامل

Microleakage comparison of three types of adhesive systems versus GIC-based adhesive in class V composite restorations

Background and aims: New dentin bonding agents and techniques have been developed to reduce microleakage and create higher bond strength. This in-vitro study compared the microleakage of three resin-based adhesives versus a GIC-based adhesive on class V composite restorations.  Materials and Methods: Class V cavities were prepared on the buccal surfaces of 72 sound premolars, randomly assigned ...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:
  • Dental materials : official publication of the Academy of Dental Materials

دوره 22 10  شماره 

صفحات  -

تاریخ انتشار 2006