Effects of vancomycin, cefazolin and test conditions on the wear behavior of bone cement.
نویسندگان
چکیده
Antibiotic cement has been recommended in the treatment of prosthetic infections. The purpose of this study was to investigate the mechanical behavioral changes in cement loaded with two antibiotics, vancomycin and cefazolin, in dry and liquid medium. Six groups and four study conditions were established according to the doses of antibiotic used and the ageing (immersion in phosphate buffered saline) of the samples. Properties evaluated were friction coefficient and wear. Samples in dry medium showed higher wears than in liquid. Antibiotic selection did not influence wear properties tested in dry conditions, however, in liquid medium, there were higher frictional coefficients and wear for cefazolin loaded cement after one week and for vancomycin and cefazolin after one month. The results suggest that antibiotic cements behave differently in liquid and that the molecular characteristics of antibiotics are essential for determining this influence.
منابع مشابه
Effect of Wet and Dry Conditions on Wear Behavior of Amorphous Coating of Fe-Cr-Mo-Nb-C-B
Recently, wear resistant properties of metallic glasses has attracted a lot of interest. Because the surface of metallic glasses are prone to phase transformation, finding the effects of test condition on structure and wear behavior of metallic glasses is important. In this research, by using an automated electrospark deposition (ESD), a layer of Fe51Cr18Mo7B16C4Nb4 was deposited on AISI 316l s...
متن کاملA Study of the Wear Behavior of a Rail Material
The rail track is one of the most important elements of a railway system. During the passage of trains, the rails are subjected to contact load that comes from the wheels of the train. The railway track often fails in service due to wear caused by contact fatigue and other wear damage mechanisms that could also limit the life span of the railway infrastructure and railway vehicle. The aim of t...
متن کاملEFFECTS OF Al-5TI-1B MASTER ALLOY AND HEAT TREATMENT ON THE MICROSTRUCTURE AND DRY SLIDING WEAR BEHAVIOR OF AN Al-12Zn-3Mg-2.5Cu ALLOY
In this study the effect of Al–5Ti–1B grain refiner on the structural characteristics and wear properties of Al–12Zn–3Mg–2.5Cu alloy was investigated. The optimum amount for Ti containing grain refiners was selected as 2 wt.%. T6 heat treatment, (i.e. heating at 460 °C for 1 h before water quenching to room temperature and then aging at 120 °C for 24 h) was applied for all specimens before wear...
متن کاملA novel test method for evaluation of the abrasive wear behaviour of total hip stems at the interface between implant surface and bone cement.
After total hip replacement, some cemented titanium stems show above-average early loosening rates. Increased release of wear particles and resulting reaction of the peri-prosthetic tissue were considered responsible. The objective was to develop a test method for analysing the abrasive wear behaviour of cemented stems and for generating wear particles at the interface with the bone cement. By ...
متن کاملInhibitory effects of vancomycin and fosfomycin on methicillin-resistant Staphylococcus aureus from antibiotic-impregnated articulating cement spacers
OBJECTIVES Vancomycin and fosfomycin are antibiotics commonly used to treat methicillin-resistant Staphylococcus aureus (MRSA) infection. This study compares the in vitro inhibitory effects against MRSA of articulating cement spacers impregnated with either vancomycin or fosfomycin. METHODS Vancomycin-impregnated articulating cement spacers and fosfomycin-impregnated articulating cement space...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید
ثبت ناماگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید
ورودعنوان ژورنال:
- The Journal of arthroplasty
دوره 29 1 شماره
صفحات -
تاریخ انتشار 2014