Stepped-end Design for Carbon Fiber -reinforced Plastic (cfrp) Bonded onto a Steel Plate under Uni-axial Load

نویسندگان

  • Toshiyuki ISHIKAWA
  • Takeshi MIYASHITA
چکیده

In the application of multiple Carbon Fiber-Reinforced Plastic (CFRP) plates onto a structural steel member, stepping of the CFRP plate ends is often adopted to prevent debonding. This approach requires the nonuniform extension of CFRP plate lengths. In this study, to shorten the length of CFRP plates, a nonuniform overlapping arrangement of several CFRP plate ends was proposed and the theoretical conditions of arrangement were proposed. Additionally, the design for the stepped-end arrangement of CFRP plates under a uni-axial load was shown. It was confirmed with stress analysis that the stress in the steel plate was reduced to the design value by bonding the CFRP plate with the proposed stepped ends.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Strengthening of Bridge G-270 with Externally Bonded Carbon Fiber Reinforced Polymer (cfrp) Prepared for the Missouri Department of Transportation in Cooperation with the U.s. Department of Transportation Federal Highway Administration

The opinions, findings and conclusions expressed in this report are those of the principal investigator and the Missouri Department of Transportation. They are not necessarily those of the U. EXECUTIVE SUMMARY This report presents the results of a pilot study to apply externally bonded Carbon Fiber Reinforced Polymer (CFRP) sheets to strengthen a simple span reinforced concrete solid slab bridg...

متن کامل

Effect of Impact Load on the Bond between Steel and CFRP Laminate

Carbon fiber reinforced polymers strengthen steel structural elements. These structural elements are normally subjected to static, dynamic and fatigue loadings during their life-time. CFRP laminate is commonly used structures under the subjected loads. A number of focused on the characteristics of CFRP sheets members under static, dynamic and fatigue loadings. is a gap in understanding the bond...

متن کامل

Dynamic Characteristics of Joined Steel and Carbon Fiber-Reinforced Plastic Tubes: Experimental and Numerical Investigation

The fundamental frequencies and mode shapes of steel and carbon fiber–reinforced plastic (CFRP) cylindrical shells with steel inserts were investigated using finite element analysis and modal testing. The free-free boundary condition was tested with modal testing using the roving hammer method and verified by finite element analysis using ABAQUS. The results show good agreement between the test...

متن کامل

Effects of Horizontal Deficiency Location on the Structural Behaviors of Steel SHS Short Columns Strengthened using CFRP

Several deficient steel structural members require to be strengthened all over the world. In this article, horizontal defects were generated at three locations (top, middle, and bottom) on the middle element and the middle of the side element. Consequently, the effects of the location of such defects on axial behavior of Carbon Fiber Reinforced Polymer (CFRP) strengthened steel Square Hollow Se...

متن کامل

A New Design Model for Adhesive Joints Used to Bond Frp Laminates to Steel Beams

The strengthening and repair of existing structures using bonded carbon fiber reinforced polymer, CFRP, laminates has attracted a great deal of attention in the past two decades. Investigations clearly indicate the great potential of this method for restoring the capacity of corroded steel beams and improving their fatigue life. One important issue regarding the use of this technique in strengt...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2012