Experimental Study on Repetition Frequency of Drop/Jet Movement in Electro-Spraying of Deionized Water

نویسندگان

  • Zhentao Wang
  • Lin Tian
  • Lei Xia
  • Jingliang Dong
  • Junfeng Wang
  • Jiyuan Tu
چکیده

The electro-spraying process can be regular and periodic, consisting of cyclical phases of initiation (meniscus, drop, and/or jet), pulsation, deformation and separation. This paper presents an experimental study on the repetition frequency of drop and/or jet ejection from the capillary end with various spraying modes during an electro-spraying process of deionized (DI) water. The influence of operating parameters such as applied voltage, liquid flow rate, electrical conductivity (DI) and the number of emitters is considered. The time evolution of drop and/or jet initiation, pulsation, deformation and separation from the capillary tip or meniscus was captured and analyzed in detail in different spraying modes. The repetition frequency was calculated offline based on the time-resolved images captured by a high-speed camera and was found to be highly affected by the electrical strength and dependent on the spraying mode. This frequency firstly increased and then decreased with an increase in applied voltage. Peak frequency and the applied voltage were related and both correlated to the liquid flow rate. The repetition frequency was very sensitive to the applied voltage at a low volume flow rate. Particular attention was given to the electro-spraying characteristics of single, double and triple emitters. The similarities and differences are discussed.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Experimental Investigation of the Effect of Deionized Water on Surface Roughness of Near Dry Electro Discharge Machining of AISI D2 Steel

The electro discharge machining (EDM), one of the methods used in the machining industry and a non-traditional manufacturing method, the electro erosion process does not depend on the hardness of material and offers a way to process materials of very complex geometry with very fine and high precision by using cheap electrode materials, which make it a preferred method. In this study, effect of ...

متن کامل

Experimental Investigation of the Effect of Deionized Water on Surface Roughness of Near Dry Electro Discharge Machining of AISI D2 Steel

The electro discharge machining (EDM), one of the methods used in the machining industry and a non-traditional manufacturing method, the electro erosion process does not depend on the hardness of material and offers a way to process materials of very complex geometry with very fine and high precision by using cheap electrode materials, which make it a preferred method. In this study, effect of ...

متن کامل

Experimental Study of Coating in a Bottom Sprayed Fluidized Bed

Several investigations have been devoted towards understanding the coating process in fluidized beds. Most of these studies focused on spraying liquid droplets over the bed. However, due to the complexity of these systems, more investigations are still required to quantify the effect of operating conditions on the coating criteria. The present work aims at fundamentally understanding and pr...

متن کامل

Reduce the maximum scour depth downstream of Flip Bucket Spillway through the spillway geometry optimization (study released spillway dam Kurdistan)

The Performance of shooting pool, in addition to the quality of the area in which the flow collides with it, depends to the height of the jet drop, the angle of the water flow, the depth of the jet and the concentration of the jet. By increasing the height of the jet drop, the fall velocity increases and subsequently the jetchr('39')s energy will be more intrusive. Different collision area from...

متن کامل

Survy of Influence of inlet Type and Position on the Performance of Jet Pulse bag house System

Background and Objective:Pulse jet systems are of interest due to their high filtration velocity,They're used as inlets from top and bottom. the purpose of this study was to compare the pressure drop and collection efficiency at the different inlet positions in a baghouse Methods and Materials:In this experimental study, a pilot system was designed at 12ft/min permeability for MDF particles.Fo...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2017