Fabrication of Bacteria Environment Cubes with Dry Lift-Off Fabrication Process for Enhanced Nitrification

نویسندگان

  • S A P L Samarasinghe
  • Yiru Shao
  • Po-Jung Huang
  • Michael Pishko
  • Kung-Hui Chu
  • Jun Kameoka
چکیده

We have developed a 3D dry lift-off process to localize multiple types of nitrifying bacteria in polyethylene glycol diacrylate (PEGDA) cubes for enhanced nitrification, a two-step biological process that converts ammonium to nitrite and then to nitrate. Ammonia-oxidizing bacteria (AOB) is responsible for converting ammonia into nitrite, and nitrite-oxidizing bacteria (NOB) is responsible for converting nitrite to nitrate. Successful nitrification is often challenging to accomplish, in part because AOB and NOB are slow growers and highly susceptible to many organic and inorganic chemicals in wastewater. Most importantly, the transportation of chemicals among scattered bacteria is extremely inefficient and can be problematic. For example, nitrite, produced from ammonia oxidation, is toxic to AOB and can lead to the failure of nitrification. To address these challenges, we closely localize AOB and NOB in PEGDA cubes as microenvironment modules to promote synergetic interactions. The AOB is first localized in the vicinity of the surface of the PEGDA cubes that enable AOB to efficiently uptake ammonia from a liquid medium and convert it into nitrite. The produced nitrite is then efficiently transported to the NOB localized at the center of the PEGDA particle and converted into non-toxic nitrate. Additionally, the nanoscale PEGDA fibrous structures offer a protective environment for these strains, defending them from sudden toxic chemical shocks and immobilize in cubes. This engineered microenvironment cube significantly enhances nitrification and improves the overall ammonia removal rate per single AOB cell. This approach-encapsulation of multiple strains at close range in cube in order to control their interactions-not only offers a new strategy for enhancing nitrification, but also can be adapted to improve the production of fermentation products and biofuel, because microbial processes require synergetic reactions among multiple species.

برای دانلود رایگان متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Si Oxidation and Lift - off Patterning Group 5 : Mohmmad Tanvir Alam

This report shows the analysis of two essential processes in the integrated circuit fabrication: SiO2 growth and metal deposition. The first part consists of the characterization of dry and wet thermal oxidation. The idea is to obtain the parameters that describe the behavior of this process and use this to predict specific oxidation times and thicknesses. The second part consists of metal depo...

متن کامل

Si Oxidation and Lift - off Patterning Group 5 : Mohmmad Tanvir Alam Wayne Buckhanan Hubert George

This report shows the analysis of two essential processes in the integrated circuit fabrication: SiO2 growth and metal deposition. The first part consists of the characterization of dry and wet thermal oxidation. The idea is to obtain the parameters that describe the behavior of this process and use this to predict specific oxidation times and thicknesses. The second part consists of metal depo...

متن کامل

A Micro Oxygen Sensor Based on a Nano Sol-Gel TiO2 Thin Film

An oxygen gas microsensor based on nanostructured sol-gel TiO2 thin films with a buried Pd layer was developed on a silicon substrate. The nanostructured titania thin films for O2 sensors were prepared by the sol-gel process and became anatase after heat treatment. A sandwich TiO2 square board with an area of 350 μm × 350 μm was defined by both wet etching and dry etching processes and the wet ...

متن کامل

Exploration of waveguide fabrication from thermally evaporated Ge–Sb–S glass films

Waveguides from thermally evaporated Ge23Sb7S70 films have been fabricated using both plasma etching and lift-off techniques. The two methods have been compared in their ability to provide high quality, low-loss waveguides for microphotonics applications. We have demonstrated in this paper that low-loss 3 lm and 4 lm wide channel waveguides can be fabricated using CHF3 and SF6 plasma etching, a...

متن کامل

Wafer-scale bioactive substrate patterning by chemical lift-off lithography

The creation of bioactive substrates requires an appropriate interface molecular environment control and adequate biological species recognition with minimum nonspecific attachment. Herein, a straightforward approach utilizing chemical lift-off lithography to create a diluted self-assembled monolayer matrix for anchoring diverse biological probes is introduced. The strategy encompasses convenie...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

عنوان ژورنال:

دوره 11  شماره 

صفحات  -

تاریخ انتشار 2016