High Conductivity and Adhesion of Cu-Cr-Zr Alloy for TFT Gate Electrode

نویسندگان

  • Junbiao Peng
  • Kuankuan Lu
  • Shiben Hu
  • Zhiqiang Fang
  • Honglong Ning
  • Jinglin Wei
  • Zhennan Zhu
  • Yicong Zhou
  • Lei Wang
  • Rihui Yao
  • Xubing Lu
چکیده

Junbiao Peng 1, Kuankuan Lu 1, Shiben Hu 1 ID , Zhiqiang Fang 1, Honglong Ning 1,* ID , Jinglin Wei 1, Zhennan Zhu 1, Yicong Zhou 1, Lei Wang 1, Rihui Yao 1,* ID and Xubing Lu 2 1 Institute of Polymer Optoelectronic Materials and Devices, State Key Laboratory of Luminescent Materials and Devices, South China University of Technology, Guangzhou 510640, China; [email protected] (J.P.); [email protected] (K.L.); [email protected] (S.H.); [email protected] (Z.F.); [email protected] (J.W.); [email protected] (Z.Z.); [email protected] (Y.Z.); [email protected] (L.W.) 2 Institute for Advanced Materials and Guangdong Provincial Key Laboratory of Quantum Engineering and Quantum Materials, South China Normal University, Guangzhou 510006, China; [email protected] * Correspondence: [email protected] (H.N.); [email protected] (R.Y.); Tel.: +86-20-8711-4525 (H.N.)

برای دانلود رایگان متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Grain Refinement and Mechanical Properties of Cu–Cr–Zr Alloys with Different Nano-Sized TiCp Addition

The TiCp/Cu master alloy was prepared via thermal explosion reaction. Afterwards, the nano-sized TiCp/Cu master alloy was dispersed by electromagnetic stirring casting into the melting Cu-Cr-Zr alloys to fabricate the nano-sized TiCp-reinforced Cu-Cr-Zr composites. Results show that nano-sized TiCp can effectively refine the grain size of Cu-Cr-Zr alloys. The morphologies of grain in Cu-Cr-Zr c...

متن کامل

Production of Cu-Cr-Zr Alloy Using Electro Slag Remelting Technique (RESEARCH NOTE)

This study focused on the effect of electro slag remelting process (ESR) on microstructure and composition of an as-cast alloy of Cu-Cr-Zr. These observations revealed that applying ESR process results in a more uniform distribution of alloying elements, however a slight aggregation of large precipitates and inclusions existed in as-cast ingot was found. Additionally, impurities like P, S and M...

متن کامل

Effect of Post Treatment For Cu-Cr Source/Drain Electrodes on a-IGZO TFTs

We report a high-performance amorphous Indium-Gallium-Zinc-Oxide (a-IGZO) thin-film transistor (TFT) with new copper-chromium (Cu-Cr) alloy source/drain electrodes. The TFT shows a high mobility of 39.4 cm 2 ·V - 1 ·s - 1 a turn-on voltage of -0.8 V and a low subthreshold swing of 0.47 V/decade. Cu diffusion is suppressed because pre-annealing can protect a-IGZO from damage during the electrode...

متن کامل

Optimization of micro hardness of nanostructure Cu-Cr-Zr alloys prepared by the mechanical alloying using artificial neural networks and genetic algorithm

Cu–Cr-Zr alloys had wide applications in engineering applications such as electrical and welding industrial especially for their high strength, high electrical as well as acceptable thermal conductivities and melting points. It was possible to prepare the nano-structure of these age hardenable alloys using mechanical alloying method as a cheap and mass production technique to prepare the non-eq...

متن کامل

Effect of Chromium Behavior on Mechanical and Electrical Properties of P/M Copper-Chromium Alloy Dispersed with VGCF

Microstructural and electrical properties of Cu-chromium alloy (Cu-Cr) dispersed with vapor-grown carbon fiber (VGCF) prepared by powder metallurgy (P/M) process have been investigated. Cu-0.7 mass% Cr pre-alloyed powder (Cu-Cr) made by water atomization process was used as raw materials, which contained solid solute Cr elements in Cu matrix. The alloy powder coated with un-bundled VGCF by usin...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2017