Strategies used to stabilize the elbow joint challenged by inverted pendulum loading.
نویسندگان
چکیده
The stiffness of activated muscles may stabilize a loaded joint by preventing perturbations from causing large displacements and injuring the joint. Here the elbow muscle recruitment patterns were compared with the forearm loaded vertically (a potentially unstable inverted pendulum configuration) and with horizontal loading. Eighteen healthy subjects were studied with the forearm vertical and supinated and the elbow flexed approximately 90 degrees. In the first experiment EMG electrodes recorded activity of biceps, triceps, and brachioradialis muscles for joint torques produced (a) by voluntarily exerting a horizontal force isometrically (b) by voluntarily flexing and extending the elbow while the forearm was loaded vertically with 135N. The relationship between the EMG and the torque generated was quantified by the linear regression slope and zero-torque intercept. In a second experiment a vertical load increasing linearly with time up to 300N was applied. In experiment 1 the EMG-torque relationships for biceps and triceps had an intercept about 10% of maximum voluntary effort greater with the vertical compared to the horizontal force, the inverse was found for Brachioradialis, but the EMG-torque slopes for both agonist and antagonistic muscles were not different. In experiment 2 there were 29 trials with minimal elbow displacement and all the three muscles activated on the order of 11% of maximum activation to stabilize the elbow; 19 trials had small elbow extension and 14 trials small flexion requiring altered muscle forces for equilibrium; 7 trials ended in large unstable displacement or early termination of the test. An analysis indicate that the observed levels of muscle activation would only provide stability if the muscles' short-range stiffness was at the high end of the published range, hence the elbow was marginally stable. The stability analysis also indicated that the small elbow extension increased stability and flexion decreased stability.
منابع مشابه
MINIMUM TIME SWING UP AND STABILIZATION OF ROTARY INVERTED PENDULUM USING PULSE STEP CONTROL
This paper proposes an approach for the minimum time swing upof a rotary inverted pendulum. Our rotary inverted pendulum is supported bya pivot arm. The pivot arm rotates in a horizontal plane by means of a servomotor. The opposite end of the arm is instrumented with a joint whose axisis along the radial direction of the motor. A pendulum is suspended at thejoint. The task is to design a contro...
متن کاملModel Predictive Control and Stability Analysis of a Standing Biped with Toe-Joint
In this paper standing balance control of a biped with toe-joint is presented. The model consists of an inverted pendulum as the upper body and the foot contains toe-joint. The biped is actuated by two torques at ankle-joint and toe-joint to regulate the upper body in upright position. To model the interaction between foot and the ground, configuration constraints are defined and utilized. To s...
متن کاملA Simple Computer Control Method of Inverted Pendulum
In order to guarantee real time, a simple control method is presented to stabilize the fast-moving systeminverted pendulum. The method was obtained by mathematical derivation based on the dynamical model of the inverted pendulum system, but the control strategy is independent of the model. It is applicable for controlling other multi input single output plants besides inverted pendulum. A contr...
متن کاملInverted Pendulum Control Using Negative Data
In the training phase of learning algorithms, it is always important to have a suitable training data set. The presence of outliers, noise data, and inappropriate data always affects the performance of existing algorithms. The active learning method (ALM) is one of the powerful tools in soft computing inspired by the computation of the human brain. The operation of this algorithm is complete...
متن کاملRobust Control of an Inverted Pendulum on a Cart
This paper investigates the design and analysis of three controllers used to stabilize an inverted pendulum on a cart. This is accomplished by decomposing each control algorithm into two separate phases: swing-up control and stabilization control. A classical, H2, and H∞ design are each considered to stabilize a nominal linearized model of the inverted pendulum on a cart in the upward vertical ...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید
ثبت ناماگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید
ورودعنوان ژورنال:
- Journal of biomechanics
دوره 33 6 شماره
صفحات -
تاریخ انتشار 2000