Results of early phase of series production of ATLAS SCT barrel hybrids and modules

نویسندگان

  • M. Goodrick
  • J. Wilson
چکیده

A status of early series production of the barrel hybrids and modules of the ATLAS Semiconductor Tracker (SCT) is reported. 120 hybrids (with ASIC’s) and 98 modules were fabricated in Japan by the mid. August 2002 and gone through extensive quality assurance tests. Defective channels were found much less than 1% in hybrids and still less than 1% in modules. No increase of defective channels was observed, in hybrids after 100-hours burn-in at an elevated temperature, and in modules after thermal cycling and 24-hrs long-term test at the operation temperature of the experiment.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

ATLAS SCT Hybrids Experience

The hybrids of ATLAS semi-conductor tracker (SCT) were made with Cu/Polyimide flex-circuits, reinforced with carbon-carbon substrates, in the barrel and in the endcap modules. We report successes, problems and solutions in the course of production of 2600 pieces of hybrids each.

متن کامل

Construction and performance of the ATLAS silicon microstrip barrel modules

The ATLAS Semiconductor Tracker (SCT) consists of four barrel cylinders and 18 end-cap disks. This paper describes the SCT modules of the barrel region, of which more than 2000 are about to be constructed. The module design is fixed. Its design concept is given together with the electrical, thermal and mechanical specifications. The preseries production of the barrel modules is underway using m...

متن کامل

Diagnostic Analysis of Silicon Strips Detector Readout in the ATLAS Semi-Conductor Tracker Module Production

The ATLAS Semi-Conductor Tracker (SCT) Collaboration is currently in the production phase of fabricating and testing silicon strips modules for the ATLAS detector at the Large Hadron Collider being built at the CERN laboratory in Geneva, Switzerland. A small but relevant percentage of ICs developed a new set of defects after being mounted on hybrids that were not detected in the wafer screening...

متن کامل

Design and development of a work robot to place ATLAS SCT modules onto barrel cylinders

More than 2000 silicon modules need to be placed and fastened on the ATLAS SCT barrel tracker. A semi-automatic pick-and-place work robot was designed and developed to cope with the module placement for the SCT barrel assembly. We found that this robot could place modules to a mechanical precision of better than 25 mm. r 2005 Elsevier B.V. All rights reserved. PACS: 29.40.Gx; 29.40.Wk; 29.90.+r

متن کامل

Robotic mounting of ATLAS barrel SCT modules

The 2112 silicon detector modules of the barrel part of the ATLAS SemiConductor Tracker (SCT) have been mounted on their carbon fibre support structure. Module insertion, placement and fixing were performed by robotic assembly tooling. We report on our experience with this assembly method. Part of the mounting sequence involves a partial survey of elements of the support structure which is need...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2002