Modeling of Losses Due to Inter-Laminar Short-Circuit Currents in Lamination Stacks

نویسندگان

  • S. B. Shah
  • A. Arkkio
چکیده

The cores of electrical machines are generally punched and laminated to reduce the eddy current losses. These manufacturing processes such as punching and cutting deform the electrical sheets and deteriorate its magnetic properties. Burrs are formed due to plastic deformation of electrical sheets. Burr formed due to punching on the edges of laminated sheets impairs the insulation of adjacent sheet and make random galvanic contacts during the pressing of stacked sheets. The effect of circulating current occurs if the burrs occur on the opposite edges of the stacks of laminated sheets and incase of bolted or wielded sheets, induced current return through it. This induced current causes the additional losses in electrical machine. The existence of surface current on the boundary between two insulated regions causes discontinuity of tangential component of magnetic field. Hence, based on this principle, the boundary layer model was developed to study the additional losses due to galvanic contacts formed by burred edges. The boundary layer model was then coupled with 2-D finite element vector potential formulation and compared with fine mesh layer model. Fine mesh layer model consist of finely space discretized 950028 second order triangular elements. The losses were computed from two models and were obtained similar at 50 Hz. The developed boundary layer model can be further used in electrical machines to study additional losses due galvanic contacts at the edges of stator cores.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Determination of Optimal Allocation and Penetration Level of Distributed Energy Resources Considering Short Circuit Currents

The integration of Distributed Energy Resources (DER) in the distribution network has plenty of advantages if their allocation and Penetration Level (PL) are done appropriately. Hence, the challenge of finding the best allocation and PL of DERs in large distribution networks is an important but intricate problem. This paper proposes a novel methodology to simultaneously determine the optimal lo...

متن کامل

Induction machine stray loss from inter-bar currents

Stray load loss refers generally to the sources of induction machine loss not accounted for by typical calculations of primary or secondary copper loss, no load core loss, or friction and windage loss. Harmonic rotor bar currents from the non-sinusoidal distribution of the slotted stator winding contribute significant stray load loss. Rotor bars, especially on cast rotors for machines under fif...

متن کامل

A Comprehensive Mathematical Model for Analysis of WR-Resolvers under Stator Short Circuit Fault

Wound-Rotor (WR) resolvers are the most widely used position sensors in applications with harsh environmental conditions. However, their performance is exposed to failure due to the high risk of short circuit (SC) fault. Although the output current of the resolver is negligible, its thin copper wires increase the probability of the short circuit fault. To avoid the propagation of the turn-to-tu...

متن کامل

Structure Properties of Laminar Currents on P2

We study the structure of a class of laminar closed positive currents on CP, naturally appearing in birational dynamics. We prove such a current admits natural non intersecting leaves, that are closed under analytic continuation. As a consequence it can be seen as a foliation cycle a weak lamination.

متن کامل

Influence of Converter and inverter on dynamic behavior of the GMAW process

This paper investigates the dynamic behavior of Gas Metal Arc Welding (GMAW) process for two types of power supplies –inverter and rectifier- for short circuit transfer mode. The large ripples on the rectifier power source are able to perturb the metal transfer mode. In this experimental work some operating points in the short circuit mode have been selected using an automatic pipeline welding ...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2013