Cytotoxicity of urethane dimethacrylate composites before and after aging and leaching.

نویسندگان

  • N M Mohsen
  • R G Craig
  • C T Hanks
چکیده

The in vitro cytotoxicity of urethane dimethacrylate composites cured at different times by visible light and after different aging times and extraction treatments was evaluated using succinic dehydrogenase activity in the mitochondria of a fibroblastic cell line to reflect cell viability. In addition, extractable chemicals associated with cell response were identified. The composite samples were tested untreated, polished, or extracted with water or 75% ethanol-water. Balb/c 3T3 fibroblasts were used as the cell culture system while MTT-formazan production was used as the toxicity parameter. Cell viability was calculated as a percentage of Teflon controls. Identification of the chemicals was measured by extracting the composites with 75% ethanol-water, separating the extract by HPLC, and identifying the fractions with mass spectroscopy. In general, cell viability increased continuously with curing time for differently treated samples at high aging times (288 h) while it decreased when the composites were not aged (0 h). In addition, for 75% ethanol or water-extracted composites, cell viability increased within the first 24 h of aging and reached a plateau after 72 h. Lowest cytotoxicity occurred when the samples were extracted with the 75% ethanol solution. The highest cytotoxic effects were found when the samples were untreated. Slightly reduced cytotoxic effects were seen with polished composites. The results suggest that curing the light-activated composites for a minimum of 150 s and post-curing for 24 h is required to attain comparable biocompatibility with the Teflon control. Removing the oxygen-inhibited layer from these composites decreased the cytotoxicity by 33% while extracting the composites with 75% ethanol-water decreased it by 77%. Chemicals released from the surface accounted for approximately 40% of cellular response while about 60% of the response was due to chemical components released from the bulk. The primary leachable component from the composites was UDMA monomer. Small quantities of 1,6 hexane diol methacrylate, camphoroquinone, and 2,4,6-tritertiarybutyl phenol also were found.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Monomer Release from Nanofilled and Microhybrid Dental Composites after Bleaching

OBJECTIVE The aim of this study was to assess the effect of bleaching on elution of monomers from nanofilled and microhybrid composites. MATERIALS AND METHODS 80 samples (5mm diameter and 3mm thickness) of each composite were prepared. After curing, half of them were randomly polished. Each group was divided into 8 subgroups and immersed in water or 10%, 20% and 30% H2O2 for 3 or 8 hours. Elu...

متن کامل

Poly(propylene glycol) and urethane dimethacrylates improve conversion of dental composites and reveal complexity of cytocompatibility testing.

OBJECTIVES To determine the effects of various monomers on conversion and cytocompatibility of dental composites and to improve these properties without detrimentally affecting mechanical properties, depth of cure and shrinkage. METHODS Composites containing urethane dimethacrylate (UDMA) or bisphenol A glycidyl methacrylate (Bis-GMA) with poly(propylene glycol) dimethacrylate (PPGDMA) or tri...

متن کامل

Monomers used in resin composites: degree of conversion, mechanical properties and water sorption/solubility.

The organic phase of resin composites is constituted by dimethacrylate resins, the most common monomers being the bisphenol A diglycidildimethacrylate (BisGMA), its ethoxylated version (BisEMA), triethylene glycol dimethacrylate (TEGDMA) and urethane dimethacrylate (UDMA). This study compared the homopolymers formed from the monomers used in restorative dental composites in terms of their degre...

متن کامل

Degree of Conversion and BisGMA, TEGDMA, UDMA Elution from Flowable Bulk Fill Composites.

The degree of conversion (DC) and the released bisphenol A diglycidyl ether dimethacrylate (BisGMA), triethylene glycol dimethacrylate (TEGDMA) and urethane dimethacrylate (UDMA) monomers of bulk-fill composites compared to that of conventional flowable ones were assessed using micro-Raman spectroscopy and high performance liquid chromatography (HPLC). Four millimeter-thick samples were prepare...

متن کامل

Hydrolytic stability of silanated zirconia-silica-urethane dimethacrylate composites.

The effect of the method of silanation of zirconia-silica by 3-methacryloxypropyltrimethoxysilane (MAPM) and 3-acryloxypropyltrimethoxysilane (APM) on the diametral tensile and transverse strength of composites made from these silanated fillers and a urethane dimethacrylate was determined after 0-108 h of boiling in water. The water sorption of these composites was also measured at times up to ...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:
  • Journal of biomedical materials research

دوره 39 2  شماره 

صفحات  -

تاریخ انتشار 1998