Development and evaluation of optimized sucrose ester stabilized oleanolic acid nanosuspensions prepared by wet ball milling with design of experiments.

نویسندگان

  • Wenji Li
  • Ka-yun Ng
  • Paul Wan Sia Heng
چکیده

The aim of this study was to develop optimized sucrose ester (SE) stabilized oleanolic acid (OA) nanosuspensions (NS) for enhanced delivery via wet ball milling by design of experiments (DOE). In this study, SEOA NS batches were prepared by wet ball milling method. Mean particle sizes and polydispersity indices were determined using a nanosizer. The percent encapsulation efficiency, saturation solubility and in vitro dissolution rate were obtained with analyses using HPLC. Preparation methods were optimized by DOE using the Minitab software. The in vitro bioefficacy was obtained by methyl thiazolyl tetrazolium (MTT) measurements in A549 human non small cell lung cancer cell line. The in vivo pharmacokinetics profile was determined using LC-electrospray ionization (ESI)-MS/MS. The study produced spherical SEOA NS particles (ca. 100 nm in diameter) which were found to be able to increase OA saturation solubility considerably. Optimized SEOA-GBD NS (milled at 600 rpm for 3 h, sucrose monolaurate (SEL) : sucrose monopalmitate (SEP) at 9 : 1, w/w; SE : OA at 1 : 1, w/w) was found to be physically stable over 14 d at 4°C. The NS showed much higher dissolution rate, cytotoxicity and bioavailability when compared with the free drug. Thus, the prepared OA as SE stabilized NS particles by wet ball milling enhanced the saturation solubility, in vitro dissolution rate, bioefficacy and in vivo bioavailability of OA. The use of sugar esters may also be potentially applied to other hydrophobic drugs.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Plant-Mediated Synthesis of Silver Nanoparticles and Their Stabilization by Wet Stirred Media Milling

Within this study, a stable nanosuspension of silver nanoparticles (Ag NPs) was prepared using a two-step synthesis and stabilization approach. The Ag NPs were synthesized from a silver nitrate solution using the Origanum vulgare L. plant extract as the reducing agent. The formation of nanoparticles was finished upon 15 min, and subsequently, stabilization by polyvinylpyrrolidone (PVP) using we...

متن کامل

Kanemite: an easily prepared and highly efficient catalyst for biodiesel production optimized by response surface methodology

Kanemite was readily prepared and used as solid base catalyst for transesterification of sunflower oil to fatty acid methyl ester (FAME). The catalyst was characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), N2 adsorption-desorption and field emission scanning electron microscopy (FESEM) techniques. Central Composite Design (CCD) coupled with Response Surfac...

متن کامل

Solubility Study in Ag-Cu Binary System Prepared By Ball Milling Process

Solid solutions of Ag-Cu were prepared via ball milling process, for about 5-30 h. The Cu-20at%Ag and Cu-3.64at%Ag composition were investigated by X-ray diffraction technique. It was realized that the solid solubility level could be increased by increasing the initial solute content in the mixture. In addition, shifts in peak positions of silver and copper were observed with milling time. The ...

متن کامل

Hydrocortisone nanosuspensions for ophthalmic delivery: A comparative study between microfluidic nanoprecipitation and wet milling.

Recently, drug nanosuspensions have shown a potential for ophthalmic delivery. In this study, a hydrocortisone (HC) nanosuspension (NS) was developed using microfluidic nanoprecipitation as a recent, simple and cost-effective bottom-up technique of drug nanonization. For comparison, a second HC NS was prepared by top-down wet milling procedures. The produced nanosuspensions were characterized f...

متن کامل

Effect of Mechanical Milling on the Morphologyand Structural Evaluation of Al-Al2O3 Nanocomposite Powders

The morphological and microstructural changes during mechanical milling of Al powder mixed with 2.5, 5 and 10 wt.% Al2O3 particles were studied. The milling was performed in a planetary ball mill for various times up to 20 h. The produced composite powders were investigated using X-ray diffraction pattern (XRD) to elucidate the role of particle size, secondary phase content and milling time on ...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:
  • Biological & pharmaceutical bulletin

دوره 37 6  شماره 

صفحات  -

تاریخ انتشار 2014