Laser ablation- and plasma etching-based patterning of graphene on silicon-on-insulator waveguides.

نویسندگان

  • Jürgen Van Erps
  • Tymoteusz Ciuk
  • Iwona Pasternak
  • Aleksandra Krajewska
  • Wlodek Strupinski
  • Steven Van Put
  • Geert Van Steenberge
  • Kitty Baert
  • Herman Terryn
  • Hugo Thienpont
  • Nathalie Vermeulen
چکیده

We present a new approach to remove monolayer graphene transferred on top of a silicon-on-insulator (SOI) photonic integrated chip. Femtosecond laser ablation is used for the first time to remove graphene from SOI waveguides, whereas oxygen plasma etching through a metal mask is employed to peel off graphene from the grating couplers attached to the waveguides. We show by means of Raman spectroscopy and atomic force microscopy that the removal of graphene is successful with minimal damage to the underlying SOI waveguides. Finally, we employ both removal techniques to measure the contribution of graphene to the loss of grating-coupled graphene-covered SOI waveguides using the cut-back method.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Fabrication and Optical Characterization of Silicon Nanostructure Arrays by Laser Interference Lithography and Metal-Assisted Chemical Etching

In this paper metal-assisted chemical etching has been applied to pattern porous silicon regions and silicon nanohole arrays in submicron period simply by using positive photoresist as a mask layer. In order to define silicon nanostructures, Metal-assisted chemical etching (MaCE) was carried out with silver catalyst. Provided solution (or materiel) in combination with laser interference lithogr...

متن کامل

Low-Loss Amorphous Silicon-On-Insulator Technology for Photonic Integrated Circuitry

We report the fabrication of low-loss amorphous silicon photonic wires deposited by plasma enhanced chemical vapor deposition. Single mode photonic wires were fabricated by 193nm optical lithography and dry etching. Propagation loss measurements show a loss of 3.46dB/cm for photonic wires (480×220nm) and 1.34dB/cm for ridge waveguides.

متن کامل

Low-Loss Slot Waveguides with Silicon (111) Surfaces Realized Using Anisotropic Wet Etching

We demonstrate low-loss slot waveguides on silicon-on-insulator platform. Waveguides oriented along the (11-2) direction on the Si (110) plane were first fabricated by a standard e-beam lithography and dry etching process. A tetramethylammonium hydroxide-based anisotropic wet etching technique was then used to remove any residual side wall roughness. Using this fabrication technique, propagatio...

متن کامل

A new low-temperature high-aspect-ratio MEMS process using plasma activated wafer bonding

This paper presents the development and characterization of a new high-aspect-ratio MEMS process. The silicon-on-silicon (SOS) process utilizes dielectric barrier discharge surface activated low-temperature wafer bonding and deep reactive ion etching to achieve a high aspect ratio (feature width reduction-to-depth ratio of 1:31), while allowing for the fabrication of devices with a very high an...

متن کامل

Monolithic integration of erbium-doped amplifiers with silicon-on-insulator waveguides.

Monolithic integration of Al2O3:Er3+ amplifier technology with passive silicon-on-insulator waveguides is demonstrated. A signal enhancement of >7 dB at 1533 nm wavelength is obtained. The straightforward wafer-scale fabrication process, which includes reactive co-sputtering and subsequent reactive ion etching, allows for parallel integration of multiple amplifier and laser sections with silico...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:
  • Optics express

دوره 23 20  شماره 

صفحات  -

تاریخ انتشار 2015