Design and Fabrication of an Instrumented Handrim to Measure the Kinetic and Kinematic Information by the Hand of User for 3D Analysis of Manual Wheelchair Propulsion Dynamics

نویسندگان

  • Mohammadreza Mallakzadeh
  • Hossein Akbari
چکیده

The repetitious nature of propelling a wheelchair has been associated with the high incidence of injury among manual wheelchair users (MWUs), mainly in the shoulder, elbow and wrist. Recent literature has found a link between handrim biomechanics and risk of injury to the upper extremity. The valid measurement of three-dimensional net joint forces and torques, however, can lead to a better understanding of the mechanisms of injury, the development of prevention techniques, and the reduction of serious injuries to the joints. In this project, an instrumented wheel system was developed to measure the applied loads dynamically by the hand of the user and the angular position of the wheelchair user's hand on the handrim during the propulsion phase. The system is composed of an experimental six-axis load cell, and a wireless eight channel data logger mounted on a wheel hub. The angular position of the wheel is measured by an absolute magnetic encoder. The angular position of the wheelchair user's hand on the handrim during the propulsion phase (ɸ) or point of force application (PFA) is calculated by means of a new-experimental method using 36 pairs of infrared emitter/receiver diodes mounted around the handrim. In this regard, the observed data extracted from an inexperienced able-bodied subject pushed a wheelchair with the instrumented handrim are presented to show the output behavior of the instrumented handrim. The recorded forces and torques were in agreement with previously reported magnitudes. However, this paper can provide readers with some technical insights into possible solutions for measuring the manual wheelchair propulsion biomechanical data.

برای دانلود رایگان متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Design and Modification of One Arm Driven Manual Hemiplegic Wheelchair

This paper presents design modification to the existing standard wheelchair by incorporating an improved propulsion system and also braking and tilting systems that allow its full control with only one hand. The proposed design has the propulsion system with a chain drive powered through a four-bar linkage driven by the main handle. The desired direction of motion is obtained by moving the leve...

متن کامل

Reliability of biomechanical variables during wheelchair ergometry testing.

Wheelchair ergometer testing is used to characterize wheelchair propulsion mechanics. The reliability of kinematic and kinetic measures has not been investigated for wheelchair ergometer testing. In this study, test-retest reliability of biomechanical measurements on a wheelchair ergometer was determined during a submaximal endurance test. Ten nondisabled subjects (seven male, three female), in...

متن کامل

The influence of speed and grade on wheelchair propulsion hand pattern.

BACKGROUND The hand pattern used during manual wheelchair propulsion (i.e., full-cycle hand path) can provide insight into an individual's propulsion technique. However, previous analyses of hand patterns have been limited by their focus on a single propulsion condition and reliance on subjective qualitative characterization methods. The purpose of this study was to develop a set of objective q...

متن کامل

Relationship between shoulder pain and kinetic and temporal-spatial variability in wheelchair users.

OBJECTIVE To examine intra-individual variability of kinetic and temporal-spatial parameters of wheelchair propulsion as a function of shoulder pain in manual wheelchair users (MWUs). DESIGN Cohort. SETTING University research laboratory. PARTICIPANTS Adults with physical disabilities (N=26) who use a manual wheelchair for mobility full time (>80% ambulation). INTERVENTIONS Participants...

متن کامل

An Investigation of Bilateral Symmetry During Manual Wheelchair Propulsion

Studies of manual wheelchair propulsion often assume bilateral symmetry to simplify data collection, processing, and analysis. However, the validity of this assumption is unclear. Most investigations of wheelchair propulsion symmetry have been limited by a relatively small sample size and a focus on a single propulsion condition (e.g., level propulsion at self-selected speed). The purpose of th...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

عنوان ژورنال:

دوره 4  شماره 

صفحات  -

تاریخ انتشار 2014