Enhanced osteoblast response to electrical discharge machining surface.
نویسندگان
چکیده
The purpose of this study is to investigate the surface characteristics and biocompatibility of titanium (Ti) surfaces modified by wire electrical discharge machining (EDM). EDM surface characteristics were evaluated by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), thin-film X-ray diffractometry (XRD) and contact angle measurements. MC3T3-E1 cell morphology, attachment and proliferation, as well as analysis of osteoblastic gene expressions, on machined surfaces and EDM surfaces were also evaluated. EDM surfaces exhibited high super hydrophilicity, due to high surface energy. XPS and XRD revealed that a passive oxide layer with certain developing thickness onto. EDM surfaces promoted cell attachment, but restrained proliferation. Counted cell numbers increased significantly on the machined surfaces as compared to the EDM surfaces. Real-time PCR analyses showed significantly higher relative mRNA expression levels of osteoblastic genes (ALP, osteocalcin, Runx2, Osterix) in cells cultured on the EDM surfaces as compared to cells cultured on the machined surfaces.
منابع مشابه
An experimental analysis and optimization of machining rate and surface characteristics in WEDM of Monel-400 using RSM and desirability approach
In the present work, an experimental investigation on wire electrical discharge machining (WEDM) of Monel-400 has been presented. Monel-400 is a nickel–copper-based alloy, mostly employed in ships and corrosion-resisting applications. Four input WEDM parameters namely discharge current (Ip), pulse-on time (Ton), pulse-off time (Toff) and servo voltage (SV) have been investigated and modeled for...
متن کاملMechanical Surface Treatments of Ti-6Al-4V Miniplate Implant Manufactured by Electrical Discharge Machining (TECHNICAL NOTE)
Present work aims at multi-mechanical surface treatment of Ti-6Al-4V based-miniplate implant manufactured by electrical discharge machining (EDM) for biomedical use. Mechanical surface treatment consists of consequent use of ultrasonic cleaning, rotary tumbler polishing, and brushing. Surface layers are analyzed employing scanning electron microscopy and energy dispersive X-ray spectroscopy. Al...
متن کاملThe Effect of Electrical Discharge Machining Parameters on Alloy DIN 1.2080 Using the Taguchi Method and Optimal Determinant
Electrical discharge machining process, is one of the most widely used methods for machining, the electrically conductive parts. In this way the tool is not in contact with the workpiece and the hardness of workpiece does not affect the machining speed. In Electrical Discharge Machining process, selection of the correct machining parameters are effective in final cost and the quality of the pro...
متن کاملFatigue Life of Graphite Powder Mixing Electrical Discharge Machining AISI D2 Tool Steel
The present paper deals with the design of experimental work matrices for two groups of experiments by using Response surface methodology (RSM). The first EDM group was dealt with the use of kerosene dielectric alone, while the second was treated by adding the graphite micro powders mixing to dielectric fluid (PMEDM). The total heat flux generated and fatigue lives after EDM and PMEDM models we...
متن کاملIntelligent Knowledge Based System Approach for Optimization of Design and Manufacturing Process for Wire-Electrical Discharge Machining
Wire electrical discharge machining (WEDM) is a method to cut conductive materials with a thin electrode that follows a programmed path. The electrode is a thin wire. Typical diameters range from .004" - .012" (.10mm - .30mm) although smaller and larger diameters are available. WEDM is a thermal machining process capable of accurately machining parts with varying hardness or complex shapes. WED...
متن کاملذخیره در منابع من
با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید
برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید
ثبت ناماگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید
ورودعنوان ژورنال:
- Dental materials journal
دوره 31 2 شماره
صفحات -
تاریخ انتشار 2012