Laser-based fabrication of polymer micropump

نویسندگان

  • Joohan Kim
  • Xianfan Xu
چکیده

Joohan Kim Xianfan Xu Purdue University School of Mechanical Engineering West Lafayette, Indiana 47907 E-mail: [email protected] Abstract. Diffuser micropumps are commonly fabricated using the standard lithography techniques with silicon as the base material. The important components of this type of micropumps are flow-directing diffusers and a moving diaphragm. Different diffuser designs show various flow rates and pump efficiency. In this work a polymer is used as the base material instead of silicon. It is demonstrated that polymer-based micropumps can be conveniently fabricated using the laser machining technique. Moreover, because of the flexibility of polymer materials, there is great potential to improve the performance of the polymer micropumps. The fluid flow inside the diffuser polymer micropump is also calculated using computational fluid dynamics methods and the simulated results are compared with the experimental data. © 2004 Society of Photo-Optical Instrumentation Engineers. [DOI: 10.1117/1.1631923]

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Excimer laser fabrication of polymer microfluidic devices

Silicon has been a primary material for fabrication of microelectromechanical systems ~microfluidic devices in MEMS! for several decades. This is due to the fact that the MEMS techniques were derived from those used for microfabrication in the semiconductor industry. These techniques are well developed, and can be readily applied for silicon based MEMS fabrication. Nowadays, alternative manufac...

متن کامل

A novel diaphragm micropump actuated by conjugated polymer petals: Fabrication, modeling, and experimental results

Micropumps have promising applications in biomedical devices andmicro total analysis systems. Conjugated polymer actuators provide an important potential mechanism for realizing micropumps because of their amenability to miniaturization and low actuation voltages. In this paper we present a novel, conjugated polymer petal-actuated diaphragm micropump, which is in contrast to the typical diaphra...

متن کامل

Modular Architecture of a Non-Contact Pinch Actuation Micropump

This paper demonstrates a modular architecture of a non-contact actuation micropump setup. Rapid hot embossing prototyping was employed in micropump fabrication by using printed circuit board (PCB) as a mold material in polymer casting. Actuator-membrane gap separation was studied, with experimental investigation of three separation distances: 2.0 mm, 2.5 mm and 3.5 mm. To enhance the micropump...

متن کامل

Design and fabrication of an ac-electro-osmosis micropump with 3D high-aspect-ratio electrodes using only SU-8

Lab-on-a-chip devices require integrated pumping and fluid control in microchannels. A recently developed mechanism that can produce fluid flow is an integrated ac-electro-osmosis micropump. However, like most electrokinetic pumps, ac-electro-osmotic pumps are incapable of handling backpressure as the pumping force mechanism acts on the surface of the fluid rather than the bulk. This paper pres...

متن کامل

ECF micropump fabricated by electroforming with novel self-aligned micro-molding technology

This paper proposes and presents a novel ECF (electro-conjugate fluid) micropump with TPSEs (triangular prism and slit electrode pair) fabricated by electroforming process using newly developed self-aligned micro molds. ECF is a kind of functional and dielectric fluid. ECF micropump is based on the principle of ECF jet, which is a powerful and active jet flow generated between electrodes immerg...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2004