Influence of the initial cooling rate from γ’ supersolvus temperatures on microstructure and phase compositions in a nickel superalloy

نویسندگان

  • Muzi Li
  • James Coakley
  • Dieter Isheim
  • Gaofeng Tian
  • Barbara Shollock
چکیده

Different cooling paths from a supersolvus temperature have been applied to FGH96, a polycrystalline nickel base superalloy for turbine disc applications, in order to simulate the different microstructures that exist through the thickness of a disc following an industrial heat treatment. Secondary and tertiary γ’ precipitate size distributions and morphology have been analysed and compared for the different heat treatments using SEM and atom probe tomography (APT). Detailed compositional data for both γ’ precipitate and γ matrix are presented, and compared to equilibrium compositions calculated by Thermo-Calc. For the heat-treatments studied, the secondary γ’ composition indicates a shell of differing composition to that towards the precipitate core. From sequential equilibria compositional calculations, it is suggested that the ‘shell’ forms at a lower temperature than the precipitate core. The fine tertiary precipitates do not show the core-shell compositional differences on continuous cooling. W peaks are noted at the γ/γ’ interfacial region, which is of significance for retarding coarsening. A γ’ depletion zone surrounds the secondary precipitates, within which the γ matrix composition differs significantly to the γ far-field values, Finally, a precipitate nucleation and growth mechanistic model is suggested based on the experimental data and Thermo-Calc calculations. M AN US CR IP T AC CE PT ED ACCEPTED MANUSCRIPT Page 2 of 38

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Evolution of the Annealing Twin Density during -Supersolvus Grain Growth in the Nickel-Based Superalloy InconelTM 718

Grain growth experiments were performed on InconelTM 718 to investigate the possible correlation of the annealing twin density with grain size and with annealing temperature. Those experiments were conducted at different temperatures in the supersolvus domain and under such conditions that only capillarity forces were involved in the grain boundary migration process. In the investigated range, ...

متن کامل

Multi-Scale Characterization of Different Generations of Gamma Prime Precipitates in Nickel-based Superalloys Using Correlative Microscopy Techniques

Nickel-based superalloys have been widely used for elevated temperature applications such as turbine disc of jet engines due to their excellent mechanical properties. The typical microstructure of these alloys primarily consists of dispersed precipitates of the ordered γ’ phase with L12 structure within a disordered face-centered cubic γ matrix. The γ -γ’ microstructure in these alloys can be c...

متن کامل

Effect of Overage Hardening Heat Treatment on the Micro Structure and Hardness of Nickel-based Super Alloy Rene-80

Rene-80 nickel-base superalloy as an alloy for production of the jet turbine blades shows high mechanical properties as well as microstructure stability during the high temperature engine operation. In this research, age hardening heat treatment cycle was done on the as-cast Rene-80 superalloy. In the following, microstructure, elemental analysis of phases and macro-hardness of the alloy before...

متن کامل

Kinetics and Mechanisms of γ′ Reprecipitation in a Ni-based Superalloy

The reprecipitation mechanisms and kinetics of γ' particles during cooling from supersolvus and subsolvus temperatures were studied in AD730(TM) Ni-based superalloy using Differential Thermal Analysis (DTA). The evolution in the morphology and distribution of reprecipitated γ' particles was investigated using Field Emission Gun Scanning Electron Microscopy (FEG-SEM). Depending on the cooling ra...

متن کامل

Investigation of the Heat Treatment Effect on Microstructures and Phases of Inconel 713C Superalloy

The application of Inconel 713C is very vast in different industries such as in automobiles, aircrafts, boilers and turbines. In this paper, Inconel 713C specimens were solutionized at 1000 and 1200 °C for 1 hours in order to study changes in phases and the structure of alloy to modify the γ' phase. The optical and the scanning electron microscopy were used to investigate the structure and the ...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2017