Low-threshold whispering-gallery-mode microlasers fabricated in a Nd:glass substrate by three-dimensional femtosecond laser micromachining.

نویسندگان

  • Jintian Lin
  • Yingxin Xu
  • Jiangxin Song
  • Bin Zeng
  • Fei He
  • Huailiang Xu
  • Koji Sugioka
  • Wei Fang
  • Ya Cheng
چکیده

We report on fabrication of whispering-gallery-mode microlasers in a Nd:glass chip by femtosecond laser three-dimensional micromachining. The main fabrication procedures include the fabrication of freestanding microdisks supported by thin pillars by femtosecond laser ablation of the glass substrate immersed in water, followed by CO2 laser annealing for surface smoothing. The quality (Q) factor of the fabricated microcavity is measured to be 1.065×10(6). Lasing is observed at a pump threshold as low as ~69 μW at room temperature with a continuous-wave laser diode operating at 780 nm. This technique allows for fabrication of microcavities of high Q factors in various dielectric materials, such as glasses and crystals.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Protein-Based Three-Dimensional Whispering-Gallery-Mode Micro-Lasers with Stimulus-Responsiveness

For the first time, proteins, a promising biocompatible and functionality-designable biomacromolecule material, acted as the host material to construct three-dimensional (3D) whispering-gallery-mode (WGM) microlasers by multiphoton femtosecond laser direct writing (FsLDW). Protein/Rhodamine B (RhB) composite biopolymer was used as optical gain medium innovatively. By adopting high-viscosity aqu...

متن کامل

Fabrication of High-Q Microresonators by Femtosecond Laser Micromachining of Optical Fiber

We report a technique to fabricate whispering gallery mode microdisk resonators using femtosecond laser micromachining and a heat reflow process to improve the optical quality of the resonator. The fabricated resonators had suppressed higher order modes with a measured Q-factor as high as 7.2× 10. The described fabrication process, which relies on material non-thermal laser ablation, offers the...

متن کامل

WGM Microrod Laser Fabricated by pulsed CO2 Laser Micromilling

Introduction Whispering Gallery Mode (WGM) microlasers have been of a great interest owing to their low threshold and narrow linewidth lasing due to their high Q and small mode volume. Most of the fabrication methods [1-3] are non-controllable and non-reproducible which rely on fiber-tip melting, such as microspheres [3, 4] or splicing of small active-fiber stubs [3]. Microresonators are realiz...

متن کامل

Whispering gallery mode microlasers and refractive index sensing based on single polymer fiber

O R IG IN A L PA ER Abstract The realization of whispering gallery mode (WGM) lasing in polymer fibers is hindered by an appropriate method to dissolve the polymer and the gain material. In this work, microfibers fabricated by directly drawing from a dye doped polymer solution are exhibited as high quality microlasers and microsensors. Multi-mode and even single-mode lasing is observed from the...

متن کامل

A thermal bistability-based method for real-time optimization of ultra-low threshold whispering gallery mode microlasers

A method based on thermal bistability for ultra-low threshold microlaser optimization is demonstrated. When sweeping the pump laser frequency across a pump resonance, the dynamic thermal bistability slows down the power variation. The resulting lineshape modification enables a real-time monitoring of the laser characteristic. We demonstrate this method for a functionalized microsphere exhibitin...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:
  • Optics letters

دوره 38 9  شماره 

صفحات  -

تاریخ انتشار 2013