Pressure and velocity distribution in the new tube of the Plabutschtunnel

نویسندگان

  • ROBERT PUCHER
  • KARL PUCHER
چکیده

The main ridge of the Alps lays just crosses Austria. Therefore it is not surprising that most highways in Austria do have to pass through a lot of road tunnels. Among these tunnels, some of the world longest tunnels for vehicle traffic are found. For safety reasons today all long road tunnels are planed with two tubes. Two tubes allow one way traffic in each tube. In the case of one way traffic it is easier to deal with the dense smoke which can be produced by heavy fires. However due do the very high cost in many cases only one tube was finished first and therefore the tunnel has to be operated with two-way traffic. After some years the second tube was opened and the traffic was changed to one-way traffic. The layout of the ventilation system must be a way, so that both cases -one way traffic and two way trafficcan be handled in normal operation and in fire situations. The authors developed system to model the ventilation system in normal operation and in fire situations. The model is used for two different situations. On the one hand the necessary regulations for the ventilation system under normal conditions are calculated, on the other and simulations can be done to foresee the influence of many changes of traffic conditions or changes in the ventilation system. For many cases the velocities in all ducts of the tunnel and the pressure distribution can be calculated. Key-words: road tunnel, ventilation, piston effect, one-way – two-way traffic Proceedings of the 5th IASME / WSEAS International Conference on Fluid Mechanics and Aerodynamics, Athens, Greece, August 25-27, 2007 307

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Analysis of pressure distribution and optimization of working conditions during push bending of circular tubes

Thin-walled tube bending is still to be considered a new and advanced technique. The process has been adopted into several industries such as aero and automotive. This process may produce a wrinkling, bulking and tearing phenomenon if the process parameters are inappropriate, especially for tubes with large diameter and thin wall thickness. Push bending process is one of the methods used for be...

متن کامل

An Optical Measurement System to Measure Velocity and Provide Shock Wave Pressure Diagrams

This paper introduces an optical measurement system for shock wave characteristics. The system works by mountinga metal plate attached to spring mounts against the shock wavefront. This set is sealed and can plot the shock wave pressure diagram by measuring plate's displacement, radiation and changing the reflection of light during shock wave conflict, and converting these optical data to volta...

متن کامل

Velocity Distribution in the 90-degree Bend based on the Probability and Entropy Concept

Practical concept of velocity distribution of pressure flow in the bends is interesting and hence, the professional engineering design has been investigated in the current study. This paper shows that velocity distribution in the bends can be analyzed in terms of the probability distributions. The concept of entropy based on the probability is an applied and new approach to achieve velocity pro...

متن کامل

PULSATILE MOTION OF BLOOD IN A CIRCULAR TUBE OF VARYING CROSS-SECTION WITH SLIP FLOW

Pulsatile motion of blood in a circular tube of varying cross-section has been developed by considering slip flow at the tube wall and the blood to be a non- Newtonian biviscous incompressible fluid. The tube wall is supposed to be permeable and the fluid exchange across the wall is accounted for by prescribing the normal velocity of the fluid at the tube wall. The tangential velocity of the fl...

متن کامل

Experimental investigation of thermal and electrical performances of a nanofluid-cooled photovoltaic/thermal system equipped with a sheet-and-grooved serpentine tube collector

Introduction: In the present experimental investigation, the thermal and electrical performances of a photovoltaic/thermal system equipped with a sheet-and-grooved serpentine tube collector are investigated. The water-magnetite nanofluid is used as the heat transfer fluid. The effect of nanoparticle volume concentration (0-1%), nanofluid mass flow rate (10-40 kg/h) and groove pitch (0, 0.54 an...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2007