Marginal Integrity of CAD/CAM Fixed Partial Dentures

نویسندگان

  • Martin Rosentritt
  • Michael Behr
  • Carola Kolbeck
  • Gerhard Handel
چکیده

OBJECTIVES Computer-aided design (CAD) and manufacturing (CAM) allows the milling of high strength zirconia fixed partial dentures (FPD), however bonding to an inert ZrO(2) ceramic surface may effect the marginal integrity of the FPDs. The aim of this investigation was to evaluate the marginal adaptation of zirconia FPDs at the interfaces between zirconia, cement, and tooth. METHODS 32 3-unit FPDs were fabricated of the CAD/CAM Y-TZP zirconia (Lava, 3M Espe, Germany) according to the manufacturers' instructions. Resin cements with corresponding primer and bonding systems were used to lute the FPDs: Compolute/EBS multi (3M Espe, Germany), Panavia F/ED (Kuraray, Japan), Variolink 2/Syntac classic (Ivoclar-Vivadent, FL) and RelyX Unicem/without treatment (3M Espe, Germany). Aualloy FPDs (BioPontostar, Bego, Germany) were cemented with RelyX Unicem and Harvard (Harvard, Germany) as the control. Marginal adaptation was evaluated with scanning electron microscopy using replica specimen before and after artificial aging. After aging, microleakage tests were performed with fuchsine solution. The interfaces between cement-tooth and cement-FPD were examined. RESULTS At the interfaces (cement-tooth and cement-FPD), the systems showed a 95% or higher perfect margin before and after aging. Only Variolink2/Syntac had a marginal adaptation, lower than a 70% perfect margin. Generally, the fuchsine penetration was below 20%, only BioPontstar/Harvard andLava/Variolink2 showed penetration results between 80% and 100%. CONCLUSION The success of the adhesive cementation of zirconia FPDs depends on the cement system. Under the conditions of this study, zirconia FPDs showed good to sufficient marginal integrity in combination with Panavia/ED, Compolute/EBS and RelyX Unicem.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Clinical gap changes after porcelain firing cycles of zirconia fixed dentures

PURPOSE The aim of this study was to measure the changes on the marginal and internal adaptation of zirconia based anterior fixed partial dentures after the porcelain firing process. MATERIALS AND METHODS A total of 34 anterior fixed partial dentures using LAVA CAD/CAM system (3M ESPE, Germany) were applied. Two silicone replicas were obtained: one is obtained before porcelain firing process ...

متن کامل

Marginal fit of anterior 3-unit fixed partial zirconia restorations using different CAD/CAM systems

PURPOSE Few studies have investigated the marginal accuracy of 3-unit zirconia fixed partial dentures (FPDs) fabricated by computer-aided design/computer-aided manufacturing (CAD/CAM) system. The purpose of this study was to compare the marginal fit of zirconia FPDs made using two CAD/CAM systems with that of metal-ceramic FPDs. MATERIALS AND METHODS Artificial resin maxillary central and lat...

متن کامل

Effect of span length on the fit of zirconia framework fabricated using CAD/CAM system

PURPOSE The purpose of this study was to evaluate the effect of the span length on the fit of zirconia framework fabricated using CAD/CAM system. MATERIALS AND METHODS Abutments for single, 4-unit and 6-unit fixed partial prostheses were fabricated. Ten zirconia frameworks were fabricated for each group. The marginal and internal gap were presented by means of replica technique and measured b...

متن کامل

A review of dental CAD/CAM: current status and future perspectives from 20 years of experience.

In this article, we review the recent history of the development of dental CAD/CAM systems for the fabrication of crowns and fixed partial dentures (FPDs), based on our 20 years of experience in this field. The current status of commercial dental CAD/CAM systems developed around the world is evaluated, with particular focus on the field of ceramic crowns and FPDs. Finally, we discuss the future...

متن کامل

مقایسه تطابق کراون‌های سرامیکی فلدسپاتیک تهیه شده از روی قالب سیلیکون افزایشی و کست گچی به وسیله دستگاه CAD-CAM

  Background and Aims: Marginal fit is one of the key factors in the success of fixed restoration. The aim of this study was to evaluate the fitness of feldespatic crowns made from additional silicon impression and gypsum cast by CAD/CAM.   Materials and Methods: 10 intact extracted upper premolar teeth were used for this experimental study. After preparation of the mounted teeth with radial sh...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:
  • European Journal of Dentistry

دوره 1  شماره 

صفحات  -

تاریخ انتشار 2007