On the application of the Kitagawa–Takahashi diagram to foreign-object damage and high-cycle fatigue
نویسندگان
چکیده
The role of foreign-object damage (FOD) and its effect on high-cycle fatigue (HGF) failures in a turbine engine Ti– 6Al–4V alloy is examined in the context of the use of the Kitagawa–Takahashi diagram to describe the limiting conditions for such failures. Experimentally, FOD is simulated by firing 1 and 3.2 mm diameter steel spheres onto the flat specimen surface of tensile fatigue specimens at velocities of 200 and 300 m/s. Such damage was found to markedly reduce the fatigue strength of the alloy, primarily due to four factors: stress concentration, microcrack formation, impact-induced plasticity and tensile residual stresses associated with the impact damage. Two groups of fatigue failures could be identified. The first group initiated directly at the impact site, and can be readily described through the use of a fatigue-crack growth threshold concept. Specifically, a Kitagawa–Takahashi approach is presented where the limiting threshold conditions are defined by the stress-concentration corrected smooth-bar fatigue limit (at microstructurally small crack sizes) and a ‘‘worst-case’’ fatigue-crack growth threshold (at larger crack sizes). The second group of failures was caused by fatigue cracks that initiated at locations far from the impact site in regions of high tensile residual stresses, the magnitude of which was computed numerically and measured experimentally using synchrotron X-ray diffraction. Specifically, these failures could be rationalized due to the superposition of the residual stresses on the farfield applied mean stress, leading to a locally elevated load ratio (ratio of minimum to maximum loads). The effects of residual stress, stress concentration, and microstructurally small cracks are combined in a modified Kitagawa– Takahashi approach to provide a mechanistic basis for evaluating the detrimental effect of FOD on HCF failures in Ti– 6Al–4V blade alloys. 2002 Elsevier Science Ltd. All rights reserved.
منابع مشابه
Foreign-object damage and high-cycle fatigue: role of microstructure in Ti–6Al–4V
The objective of this study was to evaluate the influence of microstructure on the susceptibility to high-cycle fatigue (HCF) failure in Ti–6Al–4V following foreign-object damage (FOD), specifically by comparing a fine-grained bi-modal microstructure with a coarse grained lamellar microstructure. FOD was simulated by high-velocity impacts of steel spheres on a flat surface. This caused a marked...
متن کاملIn ̄uence of foreign-object damage on crack initiation and early crack growth during high-cycle fatigue of Ti±6Al±4V
The objective of this work is to provide a rationale approach to de®ne the limiting conditions for high-cycle fatigue (HCF) in the presence of foreign-object damage (FOD). This study focused on the role of simulated FOD in aecting the initiation and early growth of small surface fatigue cracks in a Ti±6Al±4V alloy, processed for typical turbine blade applications. Using high-velocity (200±300 ...
متن کاملKitagawa-Takahashi diagrams define the limiting conditions for cyclic fatigue failure in human dentin.
As cyclic fatigue is considered to be a major cause of clinical tooth fractures, achieving a comprehensive understanding of the fatigue behavior of dentin is of importance. In this note, the fatigue behavior of human dentin is examined in the context of the Kitagawa-Takahashi diagram to define the limiting conditions for fatigue failure. Specifically, this approach incorporates two limiting thr...
متن کاملEvaluation of continuum damage at different temperatures for aluminum-silicon alloy of engine piston within low-cycle fatigue regime
In this article, the isothermal low-cycle fatigue continuum damage in the engine piston aluminum alloy has been evaluated at different temperatures. For this objective, experimental data of low-cycle fatigue tests on standard specimens were used at 280, 350 and 425°C. Based on the continuum damage mechanics method, the fatigue damage was calculated during cyclic loading. Obtained results, inclu...
متن کاملLow Cycle Fatigue Simulation of Valve Bridge Region in Cylinder Head Based on Critical Plane Model
The reason of this study is low cycle failure of cast iron cylinder head during the E5 standard durability test. The goal of the present investigation is durability test simulation and low cycle fatigue life evaluation of cast iron cylinder head. With uncouple structural analysis, preloads, thermal and mechanical load and boundary conditions are prescribed to finite element model of the cylinde...
متن کامل