An experimental comparison of equivalent terminal and rotational crossbreeding systems in swine: pig performance.

نویسندگان

  • D L Kuhlers
  • S B Jungst
  • J A Little
چکیده

Eleven thousand forty-nine pigs produced from 934 litters using 262 rotational and F1 crossbred sows were used to study differences in pig weights, survival rates and pen average daily gain, daily feed intake, and feed conversion between pigs from equivalent three-breed rotational and three-breed terminal crossbreeding systems using Duroc, Yorkshire, and Landrace breeds. Pig weights at birth and 21 and 56 d and days to reach 100 kg did not differ (P > .10) between the terminal and rotational crossbreeding systems. However, ultrasound backfat thickness of pigs from the terminal crossbreeding system was .04 cm greater (P < .007) than that of pigs from the rotational crossbreeding system. Survival rate from 56 d to 100 kg was .8% greater (P < .01) for pigs from the terminal crossbreeding system than for those from the rotational crossbreeding system. The crossbreeding system had no effect (P > .10) on survival rate at birth, from birth to 21 d, from 21 to 56 d, or from birth to 100 kg. Differences between the two crossbreeding systems were nonsignificant (P > .20) for pen average daily gain, daily feed intake, and feed conversion. Breed composition of pigs was an important source of variation (P < .01) for pig weights at birth and at 56 d. Similarly, breed composition of the pig also affected ultrasound backfat thickness at 100 kg (P < .01), but not days required to reach 100 kg (P > .10). For survival traits, only survival rate from 56 d to 100 kg was influenced by breed composition of the pig.(ABSTRACT TRUNCATED AT 250 WORDS)

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Swine BREEDING A Comparison of Mating Systems Utilizing Duroc, Hampshire and Yorkshire Breeds for Swine Production

This study utilized eight years of crossbreeding data at this station to compare the number of pigs produced by different mating systems using Duroc, Hampshire and Yorkshire breeds. Mating systems were defined to include the purebred and crossbred herds. These were herds required to produce replacement breeding stock for commercial pig production for a particular two-breed terminal, two-breed r...

متن کامل

Effect of a ring type barrier and rotational speed on leakage flow of gas turbine brush seal

This paper investigates the effect of inserting a ring type barrier on leakage flow of brush seals with different bristles clearances (the distance between bristle pack tip and rotor surface). The ring is placed on both upstream and downstream sides of the bristles. An axisymmetric CFD model is employed to calculate radial pressure distribution along backing plate, axial pressure variation on r...

متن کامل

CRACK DETECTION IN CONCRETE BEAM USING OPTIMIZATION METHOD

Structural damage detection is a field that has attracted a great interest in the scientific community in recent years. Most of these studies use dynamic analysis data of the beams as a diagnostic tool for damage. In this paper, a massless rotational spring was used to represent the cracked sections of beams and the natural frequencies and mode shape were obtained. For calculation of rotational...

متن کامل

Position Control of a Pulse Width Modulated Pneumatic Systems: an Experimental Comparison

In this study, a new adaptive controller is proposed for position control of pneumatic systems. Difficulties associated with the mathematical model of the system in addition to the instability caused by Pulse Width Modulation (PWM) in the learning-based controllers using gradient descent, motivate the development of a new approach for PWM pneumatics. In this study, two modified Feedback Error L...

متن کامل

An Estimation of Required Rotational Torque to Operate Horizontal Directional Drilling Using Rock Engineering Systems

Horizontal directional drilling (HDD) is widely used in soil and rock engineering. In a variety of conditions, it is necessary to estimate the torque required for performing the reaming operation. Nevertheless, there is not presently a convenient method to accomplish this task. In this paper, to overcome this difficulty based on the basic concepts of rock engineering systems (RES), a model for ...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:
  • Journal of animal science

دوره 72 10  شماره 

صفحات  -

تاریخ انتشار 1994