A Compact Printed Antenna for Mobile Communication
نویسندگان
چکیده
In recent years, great interest was focused on microstrip antennas for their small and good performance. With the continuous growth of wireless communication communication equipment, there are higher and higher demands feed single layer compact rectangular microstrip antenna application is proposed in this paper. Two L slits are introduced at edge of the patch to reduce the resonant frequency. proposed antenna is shown in this paper. The resonant frequencies are obtained at .9 GHz, 1.41GHz, 1.94 GHz, 3.32GHz, 5.44 GHz and 5.8 GHz with bandwidth of 10 MHz, 12 MHz, 14 MHz, 41MHz, 88MHz & 96 M -14.7 dB respectively. The size of the antenna has been reduced by 80 % when compared to a conventional microstrip patch. characteristics of the designed structure are investigated by using M configuration and low profile nature of the proposed antenna make it suitable for the applications in mobile communication sy
منابع مشابه
Design and Implementation of a Compact Super-Wideband Printed Antipodal Antenna Using Fractal Elements
A compact printed fractal antipodal bow-tie antenna is designed and implemented to simultaneously cover the operations in the C, X, and Ku-bands. It is demonstrated that by addition of small fractal elements at the sides of hexagonal arms of the bow-tie, a wide operating frequency range of 3.3 to 19.1 GHz can be covered while antenna size is only 30×34×1.2 mm3. In order to match the antenna to ...
متن کاملUWB Planar Conical Horn-Shaped Self-Complementary Bow-Tie Antenna
An ultra-wideband (UWB) self-complementary planar bow-tie antenna (SCPBTA) is proposed. The antenna consists of a printed conical horn-shaped (CHS) radiator and a counterpart CHS slot etched on a rectangular ground plane. The printed CHS radiator is connected directly to the 50Ω microstrip line by bending the end portion of the feed line. As a result, the antenna has a simple structure which do...
متن کاملA Small Printed Quadrifilar Helical Antenna for BGAN/GPS Applications
This paper presents an element of a 2×2-element array antenna for Inmarsat BGAN/GPS applications. The element is an axial mode printed quadrifilar helical antenna that has been integrated with a compact feed network to provide sequential phase rotation for circular polarization (CP) radiation. The novel integrated lumped-element feed network is designed to provide a balanced RF power to the fou...
متن کاملNew Low Cost Printed Antenna CPW-Fed for Global Positioning System, Personal Communication System and Worldwide Interoperability for Microwave Access Band Applications (TECHNICAL NOTE)
This paper presents a new design of a CPW-Fed multi bands planar antenna. This antenna can be integrated easily with passive and active elements. The proposed antenna is suitable to operate for GPS, PCS and WiMAX bands. Its entire area is 52.3x52.6mm2 and is employed on an FR-4 epoxy substrate and fed by a 50 Ohm coplanar line. The antenna parameters have been analyzed and optimized by using AD...
متن کاملMulti Attribute Analysis of a Novel Compact UWB Antenna with Via-fed Elements for Dual Band Notch Function (RESEARCH NOTE)
A compact microstrip-fed antenna with dual notched bands is proposed. First, a simple basic configuration is presented for Ultra Wide Band (UWB) applications and then the dual band notched structure is extended from the UWB one. The basic structure of the UWB antenna consists of a simple square radiating patch and a ground plane with a wide square slot on back of the substrate. A semi-circle sh...
متن کاملA compact planar ultra-wideband handset antenna with L-shaped extended ground stubs
In this letter, a compact planar ultra-wideband mobile antenna with L-shaped extended ground stubs is presented. The proposed handset antenna consists of two planar meandered monopole radiating elements, i.e., main antenna and auxiliary antenna respectively, located at the diagonal corners of mobile phone printed circuit broad with standard size of 136 × 68mm2. Each radiating element is compose...
متن کامل