Effect of Extension and Type of Composite-Restored Class II Cavities on Biomechanical Properties of Teeth: A Three Dimensional Finite Element Analysis

نویسندگان

  • Azam Valian
  • Elham Moravej-Salehi
  • Allahyar Geramy
  • Elham Faramarzi
چکیده

OBJECTIVES Controversy exists regarding cavity preparation for restoration of interproximal caries in posterior teeth in terms of preserving the tooth structure and suitable stress distribution. This study aimed to assess the effect of extension and type of class II cavities and the remaining tooth structure in maxillary premolars restored with composite resin on the biomechanical properties of teeth using finite element method (FEM). MATERIALS AND METHODS Using FEM, eight three-dimensional (3D) models of class II cavities in maxillary premolars with variable mesiodistal (MD) dimensions, variable thickness of the residual wall in-between the mesial and distal cavities and different locations of the wall were designed. Other dimensions were the same in all models. Cavities were restored with composite resin. A load equal to the masticatory force (200N) was applied to the teeth. Finite element analysis (FEA) was used to calculate the von Mises stress. RESULTS Stress in the enamel margin increased by increasing the MD dimensions of the cavities. Deviation of the residual wall between the mesial and distal cavities from the tooth center was found to be an important factor in increasing stress concentration in the enamel. Increasing the MD dimensions of the cavity did not cause any increase in stress concentration in dentin. CONCLUSION Increasing the MD dimensions of the cavities, decreasing the thickness of the residual wall between the mesial and distal cavities and its deviation from the tooth center can increase stress concentration in the enamel but not in dentin.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Finite Element Analysis of the Effect of Proximal Contour of Class II Composite Restorations on Stress Distribution

Introduction: The aim of this study was to evaluate the effect of proximal contour of class II composite restorations placed with straight or contoured matrix band using composite resins with different modulus of elasticity on stress distribution by finite element method. Methods: In order to evaluate the stress distribution of class II composite restorations using finite element method, upper ...

متن کامل

Investiagtion of microleakage in CL II composit resin restorations with two-type of Amalgams in open sandwich technique

the aim of this study was to determine the microleakage at the cervical margin of the class II composite resin syntac with and without a cervical amalgam base and to compare microleakage restoration at the occlusal margins of restorations and inferface of amalgam and composite.68 extracted sound permanent premolar were used.68 class II slot cavities were prepared in these teth.the teeth were ra...

متن کامل

Effect of Thermocycling and Type of Restorative Material on Microleakage of Class II Restorations

Objectives: Microleakage is a major cause of failure of dental restorations and results in development of secondary caries, tooth hypersensitivity and pulp pathosis. This study aimed to compare the microleakage of class II cavities filled with two types of composite resins and a compomer and subjected to thermocycling. Methods: In this in vitro experimental study, class II cavities with a gi...

متن کامل

Evaluation of stress distribution in endodontically treated teeth, restored with post and crown by finite element analysis

Evaluation of stress distribution in endodontically treated teeth, restored with post and crown by finite element analysis Dr. H. Kermanshah * - Dr. M. Mirzaee* - Dr. L. Ranjbar Omrani** *- Assistant Professor of Operative Dentistry Dept. - Faculty of Dentistry–Tehran University of Medical Sciences. **- Operative Dentistry Specialist. Background and Aim: Proper restoration of root canal treated...

متن کامل

Effect of Three Light Curing Protocols and Load Cycling on Microleakage of Class V Composite Restorations

  Objective: Different methods have been suggested to overcome the polymerization shrinkage of composite restorations. Changing the light curing protocol to improve polymerization by using new light curing units is among these methods. The new devices are more efficient, portable and durable and produce less heat. This study aimed to assess the marginal microleakage of class V composite restora...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره 12  شماره 

صفحات  -

تاریخ انتشار 2015