Evolution Strategies for Film Cooling Optimization

نویسندگان

  • Sibylle D. Müller
  • Jens H. Walther
  • Petros D. Koumoutsakos
چکیده

References 1Al Taweel, A. M., and Landau, J., “Turbulence Modulation in TwoPhase Jets,” International Journal of Multiphase Flow, Vol. 3, No. 2, 1977, pp. 341–351. 2Gore, R. A., and Crowe, C. T., “Effects of Particle Size on Modulating Turbulent Intensity,” International Journal of Multiphase Flow, Vol. 15, No. 2, 1989, pp. 279–285. 3Schreck, S., andKleis, S. J., “ModiŽ cationofGrid-GeneratedTurbulence bySolidParticles,” Journal of FluidMechanics,Vol. 249, 1993, pp. 665–688. 4Kulick, J. D., Fessler, J. R., and Eaton, J. K., “Particle Response and Turbulence ModiŽ cation in Fully Developed Channel Flow,” Journal Fluid Mechanics, Vol. 277, 1994, pp. 109–134. 5Sato, Y., Hishida, K., and Maeda, M., “Effect of Dispersed Phase on ModiŽ cation of Turbulent Flow in a Wall Jet,” Journal of Fluids Engineering, Vol. 118, No. 2, 1996, pp. 307–315. 6Chang, Y.-H., “Velocity Measurements in a Particle-Laden Round Jet Using Discriminator Laser Doppler Velocimetry,” M.S. Thesis, School of Aerospace and Mechanical Engineering, Univ. of Oklahoma, Norman, OK, Jan. 1998. 7Parthasarathy, R. N., and Faeth, G. M., “Structure of Particle-Laden Turbulent Water Jets in Still Water,” International Journal of Multiphase Flow, Vol. 13, No. 5, 1987, pp. 699–716. 8Muste, M., Parthasarathy, R. N., and Patel, V. C., “Discriminator Laser Doppler Velocimetry for Measurement of Liquid and Particle Velocities in Sediment-Laden Flows,” Experiments in Fluids, Vol. 22, No. 1, 1996, pp. 45–56. 9Ahmed, S. A., Nejad, A. S., and Al-Garni, A. Z., “A Comparative Study of the Effects of LDVVelocity Bias in the Near Field of a Turbulent Free Jet,” CanadianAeronautics and Space Journal, Vol. 41,No. 4, 1995, pp. 179–184. 10Hussein, J. H., Capp, S. P., and George, W. K., “Velocity Measurements in a High-Reynolds-Numbe r Momentum-Conserving , Axisymmetric, Turbulent Jet,” Journal of Fluid Mechanics, Vol. 258, 1994, pp. 31–75.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Shape optimization of impingement and film cooling holes on a flat plate using a feedforward ANN and GA

Numerical simulations of a three-dimensional model of impingement and film cooling on a flat plate are presented and validated with the available experimental data. Four different turbulence models were utilized for simulation, in which SST  had the highest precision, resulting in less than 4% maximum error in temperature estimation. A simplified geometry with periodic boundary conditions is de...

متن کامل

Xergy analysis and multiobjective optimization of a biomass gasification-based multigeneration system

Biomass gasification is the process of converting biomass into a combustible gas suitable for use in boilers, engines, and turbines to produce combined cooling, heat, and power. This paper presents a detailed model of a biomass gasification system and designs a multigeneration energy system that uses the biomass gasification process for generating combined cooling, heat, and electricity. Energy...

متن کامل

MODELING AND OPTIMIZATION OF SINGLE-ELEMENT BULK SiGe THIN-FILM COOLERS

Modeling and optimization of bulk SiGe thin-film coolers are described. Thin-film coolers can provide large cooling power densities compared to commercial thermoelectrics. Thin-film SiGe coolers have been demonstrated with maximum cooling of 4◦C at room temperature and with cooling power density exceeding 500 W/cm2. Important parameters in the design of such coolers are investigated theoretical...

متن کامل

Towards an Analytical Model for Film Cooling Prediction using Integral Turbulent Boundary layer

The objective of this work is to develop deep theoretical methods that are based on the solution of the integral boundary layer equations for investigating film cooling in liquid rocket engine. The integral model assumes that heat is transferred from hot free stream gas to the liquid film both by convection and radiation. The mass is transferred to the free srteam gas by the well-known blowing ...

متن کامل

Optimization of Forcing Parameters of Film Cooling Effectiveness

An optimization strategy is described that combines high-fidelity simulations with response surface construction, and is applied to pulsed film cooling for turbine blades. The response surface is constructed for the film cooling effectiveness as a function of duty cycle, in the range of DC between 0.05 and 1, and pulsation frequency St in the range of 0.2–2, using a pseudospectral projection me...

متن کامل

Control of a Simplified Unsteady Film-cooling Flow Using Gradient-based Optimization

Maximization of film-cooling effectiveness in an idealized film-cooling flow is accomplished using a gradientbased control strategy. The state equations are the two-dimensional unsteady incompressible Navier-Stokes equations along with the temperature equation. The control is a spatially and temporally varying normal velocity boundary condition subject to a constraint of zero mass and energy fl...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2000