Phenomenology of bubble nucleation in the solid-state nitrogen–polystyrene microcellular foams

نویسنده

  • Vipin Kumar
چکیده

Experimental results on bubble nucleation in the solid-state polystyrene–nitrogen system are presented. It was found that the bubble nucleation occurs over a period of approximately 30 s, and is not instantaneous as previously suggested. Over the range of nitrogen pressures explored, 4–14 MPa, the cell nucleation density increased exponentially. However this increase was many orders of magnitude less than predicted by the homogeneous nucleation model, indicating that the classical theory may not be applicable to nucleation in thermoplastic polymers near the glass transition. ©

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Nucleation Effects of Nanoparticles on Microcelluar Polystyrene Foams

Introduction Microcellular foams with cell sizes less than 10 μm and cell densities larger than 10cells/cm [1] are gaining commercial importance as lightweight structural materials. The idea of introducing small bubbles in solid polymers was first proposed by Num P. Suh [2] in 1890s and the rationale was that if the bubbles are even smaller than the critical flaws in the polymer matrix and can ...

متن کامل

Cell nucleation in solid-state polymeric foams: evidence of a triaxial tensile failure mechanism

The mechanism for nucleation phenomenon in solid-state microcellular foams is identified as a solid-state failure process. This process originates at internal flaws within the gas-polymer matrix, where it is induced by the presence of a state of hydrostatic tensile stress within the polymer matrix. The hydrostatic tensile stress is caused by the presence of the saturating gas within the polymer...

متن کامل

تأثیر نانولوله‌های کربنی بر مورفولوژی سلولی فوم‌های نانوکامپوزیتی میکروسلولار PC/EPDM

This research aimed at producing microcellular foams (with cell size of 1-10 μm and cell density above 10 9 cell/cm3) from PC/EPDM in order to use in medical devices. Due to the weak nucleation behavior of microcellular polycarbonate foams, it is difficult to prepare them. This research provides valuable information regarding the possibility of making microcellular foams from this polymer by u...

متن کامل

Impact Strength of High Density Solid-State Microcellular Polycarbonate Foams

The effect of density (relative densities 0.33 to 0.90) on the impact behavior of microcellular polycarbonate (PC) was investigated. Cell size and foaming gas content were also considered. Flexed-beam Izod impact tests were conducted and the impact strength of these foams appears to be a strong function of both density and cell size. The impact strength was observed to improve over the unproces...

متن کامل

Preparation of PMMA/MWNTs Nanocomposite Microcellular Foams by In-situ Generation of Supercritical Carbon Dioxide

Nanocomposites containing poly(methyl methacrylate) (PMMA) and surface functionalized Multi-Walled Carbon Nanotubes (MWNTs) were synthesized. The dispersion of MWNTs in PMMA was characterized using Transmission Electron Microscopy (TEM).The synthesized nanocomposites were successfully foamed using a simple method based on the in-situ generation of supercritical carbon dioxide (CO2</sub...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2005