Comparative Evaluation of Physical Properties of Four Tissue Conditioners Relined to Modeling Plastic Material

نویسندگان

  • Abbas Monzavi
  • Hakimeh Siadat
  • Mohammad Atai
  • Marzieh Alikhasi
  • Vahideh Nazari
  • Sadigheh Sheikhzadeh
چکیده

OBJECTIVE Little is known about the interaction of tissue conditioners and modeling plastics. This study evaluates the influence of a variety of commercial tissue conditioners on alteration of viscoelastic properties of modeling plastics. MATERIALS AND METHODS In this in vitro study, the dynamic viscoelastic properties of four commercially available tissue conditioners (TC), Visco-gel (VG), GC Soft-Liner (SL), FITT (FT), and Coe Comfort (CC), relined to modeling plastics with a thickness of 2mm were evaluated after 1 and 7 days of water immersion with the use of storage modulus, loss modulus, and tan delta parameters. Values for these three parameters for each tissue conditioner were statistically analyzed by Kruskal Wallis and Mann Whitney tests with P value sets at<0.05. RESULTS Complex modulus and loss tangent values of TC were not significantly different among specimens containing 0, 2, 5 and 10 wt.%-SZ, respectively. In FT and TC containing 2 wt.%-SZ, these values were not significantly different between 1 and 28 days in both water- and saliva immersions. CONCLUSION The results suggest that relining with modeling plastics does affect TC's inherent dynamic viscoelastic properties, while the other tissue conditioners investigated may be found to have changed viscoelastic properties as a consequence of vicinity to the modeling plastics.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Evaluation of antifungal and antibacterial properties of adding Ag, ZnO, Chitosan nanoparticles to tissue conditioners of complete dentures:

Introduction: Chitosan has the property of inhibition of the growth of many pathogenic bacteria and fungi. Tissue conditioners are good substances for the growth and colonization of a variety of micro-organisms. The aim of this research was to investigate the antibacterial and antifungal properties of Chitosan, ZnO and Ag nanoparticles added to tissue conditioners. Methods: In this clinical tr...

متن کامل

Effect of sealant application and thermal cycling on bond strength of tissue conditioners to acrylic resin.

The aim of this study was to evaluate the effect of sealer application and thermal cycling on the bond strength between tissue conditioners and acrylic resin, and to observe the type of bond failure. Two hundred eighty-eight specimens (10x16x3 mm) were made of an acrylic resin (Lucitone 500, Dentsply) using a metal muffle. Specimens were divided into four groups according to the tissue conditio...

متن کامل

Determination of Load and Strain-Stress Distributions in Hot Closed Die Forging Using the Plasticine Modeling Technique

An axisymmetric hot closed die-forging process has been studied by physical modeling technique using the plasticine. To observe the material flow pattern, layers of plasticine with different colors were used. The normal direction to the layers was considered a principal direction. The strain distribution was obtained by measuring the thickness of the plasticine layers. Based on the strain distr...

متن کامل

Comparative Evaluation of Surface Hardness of Different Resin-Modified Glass Ionomers and a Compomer

Introdouction: Due to the practical problems and time restriction issues in treating dental problems in children, there is a noticeable demand for the application of a convenient handling restorative material with acceptable physical-mechanical properties. The aim of this investigation was to evaluate Vickers microhardness of four tooth-colored restorative materials as a determining mechanical...

متن کامل

Grain Refinement Efficiency of Multi-Axial Incremental Forging and Shearing: A Crystal Plasticity Analysis

Severe plastic deformation is a technical method to produce functional material with special properties such as high strength and specific physical properties. Selection of an efficient severe plastic deformation for grain refinement is a challenging field of study and using a modeling technique to predict the refinement efficiency has gained a lot of attentions. A comparative study was carried...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره 10  شماره 

صفحات  -

تاریخ انتشار 2013