On - chip pulse compression

نویسنده

  • Zhongyang Li
چکیده

A chip-based temporal compressor for shortening the duration of optical pulses has been developed by scientists in Japan. The scientists at Yokohama National University made their compressor from a silicon photonic crystal waveguide. Co-propagating slow light is used as a control pulse and serves to induce carrier plasma dispersion in the waveguide through two-photon absorption. The efficiency of the effect is greatly enhanced due to the control pulse propagating in the slow-light regime. The induced dispersion is used to spectrally broaden or ‘chirp’ a signal pulse. Dispersion compensation, invoked by a series of seven pairs of integrated heaters spaced along the length of the waveguide, is then used to compress the pulse. Using the scheme, the team report compressing a 13.9 ps input pulse down to a duration of 1.4 ps, corresponding to a compression factor of 9.9. OG

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Optimization of Material Removal Rate in Electrical Discharge Machining Alloy on DIN1.2080 with the Neural Network and Genetic Algorithm

Electrical discharge machining process is one of the most Applicable methods in Non-traditional machining for Machining chip in Conduct electricity Piece that reaching to the Pieces that have good quality and high rate of machining chip is very important. Due to the rapid and widespread use of alloy DIN1.2080 in different industry such as Molding, lathe tools, reamer, broaching, cutting guillot...

متن کامل

Optical pulse compression based on nonlinear silicon waveguides and chirped Bragg gratings

Due to the growing demand for higher bandwidth, employing optical devices instead of electronic devices in data transmission systems has attracted much attention in recent years. Optical switches, modulators and wavelength converters are a few examples of the required optical devices. CMOS compatible fabrication of these devices, leads to much more growing of this technology. Optical pulse comp...

متن کامل

An Optimization on the DIN1.2080 Alloy in the Electrical Discharge Machining Process Using ANN and GA

Electrical Discharge Machining (EDM) process is one of the most widely used methods for machining. This method is used to form parts that conduct electricity. This method of machining has used for hard materials and therefore selects the correct values of parameters which are so effective on the quality machining of parts. Reaching to optimum condition of the DIN1.2080 alloy (D3) machining is v...

متن کامل

An Optimization on the DIN1.2080 Alloy in the Electrical Discharge Machining Process Using ANN and GA

Electrical Discharge Machining (EDM) process is one of the most widely used methods for machining. This method is used to form parts that conduct electricity. This method of machining has used for hard materials and therefore selects the correct values of parameters which are so effective on the quality machining of parts. Reaching to optimum condition of the DIN1.2080 alloy (D3) machining is v...

متن کامل

Extending the Radar Dynamic Range using Adaptive Pulse Compression

The matched filter in the radar receiver is only adapted to the transmitted signal version and its output will be wasted due to non-matching with the received signal from the environment. The sidelobes amplitude of the matched filter output in pulse compression radars are dependent on the transmitted coded waveforms that extended as much as the length of the code on both sides of the target loc...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2015