Generation and agglomeration behaviour of size-selected sub-nm iron clusters as catalysts for the growth of carbon nanotubes

نویسندگان

  • Ravi Joshi
  • Benjamin Waldschmidt
  • Jörg Engstler
  • Rolf Schäfer
  • Jörg J Schneider
چکیده

Mass-selected, ligand-free Fe(N) clusters with N = 10-30 atoms (cluster diameter: 0.6-0.9 nm) were implanted into [Al@SiO(x)] surfaces at a low surface coverage corresponding to a few thousandths up to a few hundredths of a monolayer in order to avoid initial cluster agglomeration. These studies are aimed towards gaining an insight into the lower limit of the size regime of carbon nanotube (CNT) growth by employing size-selected sub-nm iron clusters as catalyst or precatalyst precursors for CNT growth. Agglomeration of sub-nm iron clusters to iron nanoparticles with a median size range between three and six nanometres and the CNT formation hence can be observed at CVD growth temperatures of 750 °C. Below 600 °C, no CNT growth is observed.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Effects of Confinement in Carbon Nanotubes on the Performance and Lifetime of Fischer-Tropsch Iron Nano Catalysts

The effects of confinement in carbon nanotubes on Fischer-Tropsch (FT) activity, selectivity and lifetime of Carbon NanoTubes (CNTs) supported iron catalysts are reported. A method was developed to control the position of the catalytic sites on either inner or outer surface of carbon nanotubes. TEM analyses revealed that more than 80% of iron oxide particles can be controlled to be position...

متن کامل

Evaluation of catalyst ball-milling process on growth and diameter of carbon nanotubes on iron nanoparticles

In this study, we describe the growth of carbon nanotubes on commercial iron nanoparticles without carbon shell (Fe (nm), size 2O3 and Fe* (nm)/MgO) was carried out by mixing commercial Fe* nanoparticles (as catalyst) with Al2O3 and MgO powders (as supports)by using ball-milling method. The results show in spite of the fact that ball-milling process can have neg...

متن کامل

Evaluation of catalyst ball-milling process on growth and diameter of carbon nanotubes on iron nanoparticles

In this study, we describe the growth of carbon nanotubes on commercial iron nanoparticles without carbon shell (Fe (nm), size 2O3 and Fe* (nm)/MgO) was carried out by mixing commercial Fe* nanoparticles (as catalyst) with Al2O3 and MgO powders (as supports)by using ball-milling method. The results show in spite of the fact that ball-milling process can have neg...

متن کامل

Preparation of a Novel Super Active Fischer-Tropsch Cobalt Catalyst Supported on Carbon Nanotubes

The potential of carbon nanotubes (CNT) supported cobalt catalysts for Fischer-Tropsch (FT) reaction is shown. Using the wet impregnation method cobalt on carbon nanotubes catalysts were prepared with cobalt loading varying from 15 to 45 wt. %. The catalysts are characterized by different methods including: BET physisorption, X-ray diffraction, hydrogen chemisorption, and temperature-progra...

متن کامل

Deactivation Behavior of Carbon Nanotubes Supported Cobalt Catalysts in Fischer-Tropsch Synthesis

The effects of electronic properties of inner and outer surfaces of Carbon Nano Tubes (CNTs) on the deactivation of cobalt Fischer-Tropsch (FT) catalysts were studied. The comparative characterization of the fresh and used catalysts by TEM, XRD, TPR, BET and H2 chemisorption showed that cobalt re-oxidation, cobalt-support interactions and sintering are the main sources o...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره 2  شماره 

صفحات  -

تاریخ انتشار 2011