Inactivation of clinically relevant pathogens by photocatalytic coatings
نویسندگان
چکیده
Novel disinfection methods are being sought to provide additional means of protection in a number of areas where disease outbreaks could lead to illness or fatalities. For example, the risk of contamination arising from contact with surfaces and medical devices has received much attention due to the rise in incidence of healthcare acquired infections. It is possible that reducing bio-burden on these sites may supplement the disinfection protocols currently in place and help reduce risk of infection. Photocatalytic surfaces offer promise as innovative and cost-effective biocidal engineering solutions which address these specific problems whilst maintaining stringent health and safety controls. A method was developed to assess the disinfection efficiency of photocatalytic surfaces allowing a) determination of pathogen viability as a function of treatment time; b) assessment of the surface for viable surface bound organisms following disinfection; c) measurement of the re-growth potential of inactivated organisms. This method was used to demonstrate the inactivation of extendedspectrum beta-lactamase Escherichia coli, methicillin resistant Staphylococcus aureus, Pseudomonas aeruginosa and Clostridium difficile spores using immobilised films of commercial titania nanoparticles. 99.9% reduction in viability (a 3-log kill) was observed for all bacterial cells within 80 minutes of photocatalytic treatment. Complete surface inactivation was demonstrated and bacterial re-growth following photocatalytic treatment was not observed. Greater than 99% inactivation (2.6 log reduction) was observed when the photocatalytic surfaces were challenged with Clostridium difficile spores. The efficacy of photocatalytic disinfection to inactivate Staphyloccocus epidermidis cells within a biofilm was also demonstrated, with 3 hours treatment rendering 96.5% ± 6 of the biofilm cells on the TiO2 coated substrate non-viable. Disinfection of cells throughout the 3-4 m thick biofilm was observed.
منابع مشابه
Structural formation and photocatalytic activity of magnetron sputtered titania and doped-titania coatings.
Titania and doped-titania coatings can be deposited by a wide range of techniques; this paper will concentrate on magnetron sputtering techniques, including "conventional" reactive co-sputtering from multiple metal targets and the recently introduced high power impulse magnetron sputtering (HiPIMS). The latter has been shown to deliver a relatively low thermal flux to the substrate, whilst stil...
متن کاملKinetics of photocatalytic degradation of methylene blue on nanostructured TiO2 coatings created by sol-gel process
Sol-gel process was chosen to produce a photocatalytic film to degrade methylene blue. In order to study structural and morphological properties of the coatings, a base sol of TTIP, I-PrOH, and DEA was prepared. Then with addition of 45g/L PEG 2000, 30g/L TiO2 and 15g/L PEG 2000 + 30g/L TiO2, to the base sol, three other sols were produced. The results of this study indica...
متن کاملبررسی خواص فوتوکاتالیستی لایههای NiO/TiO2 رشد داده شده بهروش اکسیداسیون پلاسمای الکترولیتی/ رسوب الکتروفورتیک
Titanium dioxide-nickel oxide porous coatings were synthesized by Plasma Electrolytic Oxidation (PEO)/ ElectroPhoretic Deposition (EPD) in one step and within a short time. The main purpose of this research was to increase photocatalytic activity of titanium oxide by increasing surface area and coupling of titanium oxide with nickel oxide. Applied voltage effects on phase structure, surface mor...
متن کاملDeposition of Visible Light Active Photocatalytic Bismuth Molybdate Thin Films by Reactive Magnetron Sputtering
Bismuth molybdate thin films were deposited by reactive magnetron co-sputtering from two metallic targets in an argon/oxygen atmosphere, reportedly for the first time. Energy dispersive X-ray spectroscopy (EDX) analysis showed that the ratio of bismuth to molybdenum in the coatings can be effectively controlled by varying the power applied to each target. Deposited coatings were annealed in air...
متن کاملInactivated properties of activated carbon-supported TiO2 nanoparticles for bacteria and kinetic study.
The activated carbon-supported TiO2 nanoparticles (TiO2/AC) were prepared by a properly controlled sol-gel method. The effects of activated carbons (AC) support on inactivated properties of TiO2 nanoparticles were evaluated by photocatalytic inactivation experiments of Escherichia coli. The key factors affecting the inactivation efficiency were investigated, including electric power of lamp, te...
متن کامل