A Review of Cell Equalization Methods for Lithium Ion and Lithium Polymer Battery Systems
نویسندگان
چکیده
Lithium-based battery technology offers performance advantages over traditional battery technologies at the cost of increased monitoring and controls overhead. Multiple-cell Lead-Acid battery packs can be equalized by a controlled overcharge, eliminating the need to periodically adjust individual cells to match the rest of the pack. Lithium-based based batteries cannot be equalized by an overcharge, so alternative methods are required. This paper discusses several cell-balancing methodologies. Active cell balancing methods remove charge from one or more high cells and deliver the charge to one or more low cells. Dissipative techniques find the high cells in the pack, and remove excess energy through a resistive element until their charges match the low cells. This paper presents the theory of charge balancing techniques and the advantages and disadvantages of the presented methods. INTRODUCTION Lithium Ion and Lithium Polymer battery chemistries cannot be overcharged without damaging active materials [1-5]. The electrolyte breakdown voltage is precariously close to the fully charged terminal voltage, typically in the range of 4.1 to 4.3 volts/cell. Therefore, careful monitoring and controls must be implemented to avoid any single cell from experiencing an overvoltage due to excessive charging. Single lithium-based cells require monitoring so that cell voltage does not exceed predefined limits of the chemistry. Series connected lithium cells pose a more complex problem: each cell in the string must be monitored and controlled. Even though the pack voltage may appear to be within acceptable limits, one cell of the series string may be experiencing damaging voltage due to cell-to-cell imbalances. Traditionally, cell-to-cell imbalances in lead-acid batteries have been solved by controlled overcharging [6,7]. Leadacid batteries can be brought into overcharge conditions without permanent cell damage, as the excess energy is released by gassing. This gassing mechanism is the natural method for balancing a series string of lead acid battery cells. Other chemistries, such as NiMH, exhibit similar natural cell-to-cell balancing mechanisms [8]. Because a Lithium battery cannot be overcharged, there is no natural mechanism for cell equalization. Therefore, an alternative method must be employed. This paper discusses three categories of cell balancing methodologies: charging methods, active methods, and passive methods. Cell balancing is necessary for highly transient lithium battery applications, especially those applications where charging occurs frequently, such as regenerative braking in electric vehicle (EV) or hybrid electric vehicle (HEV) applications. Regenerative braking can cause problems for Lithium Ion batteries because the instantaneous regenerative braking current inrush can cause battery voltage to increase suddenly, possibly over the electrolyte breakdown threshold voltage. Deviations in cell behaviors generally occur because of two phenomenon: changes in internal impedance or cell capacity reduction due to aging. In either case, if one cell in a battery pack experiences deviant cell behavior, that cell becomes a likely candidate to overvoltage during high power charging events. Cells with reduced capacity or high internal impedance tend to have large voltage swings when charging and discharging. For HEV applications, it is necessary to cell balance lithium chemistry because of this overvoltage potential. For EV applications, cell balancing is desirable to obtain maximum usable capacity from the battery pack. During charging, an out-of-balance cell may prematurely approach the end-of-charge voltage (typically 4.1 to 4.3 volts/cell) and trigger the charger to turn off. Cell balancing is useful to control the higher voltage cells until the rest of the cells can catch up. In this way, the charger is not turned off until the cells simultaneously reach the end-of-charge voltage. END-OF-CHARGE CELL BALANCING METHODS Typically, cell-balancing methods employed during and at end-of-charging are useful only for electric vehicle purposes. This is because electric vehicle batteries are generally fully charged between each use cycle. Hybrid electric vehicle batteries may or may not be maintained fully charged, resulting in unpredictable end-of-charge conditions to enact the balancing mechanism. Hybrid vehicle batteries also require both high power charge (regenerative braking) and discharge (launch assist or boost) capabilities. For this reason, their batteries are usually maintained at a SOC that can discharge the required power but still have enough headroom to accept the necessary regenerative power. To fully charge the HEV battery for cell balancing would diminish charge acceptance capability (regenerative braking). CHARGE SHUNTING The charge-shunting cell balancing method selectively shunts the charging current around each cell as they become fully charged (Figure 1). This method is most efficiently employed on systems with known charge rates. The shunt resistor R is sized to shunt exactly the charging current I when the fully charged cell voltage V is reached. If the charging current decreases, resistor R will discharge the shunted cell. To avoid extremely large power dissipations due to R, this method is best used with stepped-current chargers with a small end-of-charge current.
منابع مشابه
Electrode Materials for Lithium Ion Batteries: A Review
Electrochemical energy storage systems are categorized into different types, according to their mechanisms, including capacitors, supercapacitors, batteries and fuel cells. All battery systems include some main components: anode, cathode, an aqueous/non-aqueous electrolyte and a membrane that separates anode and cathode while being permeable to ions. Being one of the key parts of any new electr...
متن کاملNumerical investigation of the parameters of a prismatic lithium ion battery under load for electrical vehicle
Electric vehicles and hybrid electric vehicles are a suitable alternative for vehicles with hydrocarbons fuels to reduce pollution and fossil resources. The batteries operate as the driving force for these vehicles. One of the most critical parameters of the battery is computing the state of charge (SOC). The best range for SOC of lithium-ion battery is between 20% and 90%, and charging and dis...
متن کاملThermal behavior of a commercial prismatic Lithium-ion battery cell applied in electric vehicles
This paper mainly discusses the thermal behavior and performance of Lithium-ion batteries utilized in hybrid electric vehicles (HEVs), battery electric vehicles (BEVs) and fuel cell electric vehicles (FCEVs) based on numerical simulations. In this work, the battery’s thermal behavior is investigated at different C-rates and also contour plots of phase potential for both tabs and volume-mo...
متن کاملA high performance lithium-ion battery using LiNa0.02K0.01FePO4/C as cathode material and anatase TiO2 nanotube arrays as anode material
In this paper we report on a lithium ion battery (LIB) based on improved olivine lithium iron phosphate/carbon (LiFePO4/C) as cathode material and LiNa0.02K0.01FePO4/C synthesized by sol-gel method and TiO2 nanotube arrays (TNAs) with an anatase phasesynthesized through anodization of Ti foil as an anode electrode. Crystallographic structure and surface morphology of the cathode and anode mate...
متن کاملLarge Lithium Polymer Battery Modeling for the Simulation of Hybrid Electric Vehicles Using the Equivalent Circuit Method
In the present study, a model of a large Lithium Polymer (Li-Po) battery for use in the simulation of Hybrid Electric Vehicles (HEVs) is developed. To attain this goal, an Equivalent Circuit (EC) consisting of a series resistor and two RC parallel networks is considered. The accuracy and the response time of the model for use in an HEV simulator are studied. The battery parameters identifica...
متن کاملDevelopment of Lifetime Prediction Model of Lithium-Ion Battery Based on Minimizing Prediction Errors of Cycling and Operational Time Degradation Using Genetic Algorithm
Accurate lifetime prediction of lithium-ion batteries is a great challenge for the researchers and engineers involved in battery applications in electric vehicles and satellites. In this study, a semi-empirical model is introduced to predict the capacity loss of lithium-ion batteries as a function of charge and discharge cycles, operational time, and temperature. The model parameters are obtai...
متن کامل