Marginal fit of Zirconia posterior fixed partial dentures.

نویسندگان

  • Esther Gonzalo
  • María J Suárez
  • Benjamín Serrano
  • José F L Lozano
چکیده

The aim of this study was to investigate the marginal fit of posterior fixed partial dentures (FPDs) made with 2 computer-aided design/computer-assisted manufacture systems--Procera Bridge Zirconia (Nobel Biocare) and Lava AllCeramic System (3M ESPE)--and to analyze the differences between abutments and between buccal and lingual surfaces. Twenty standardized specimens were prepared to receive posterior 3-unit FPDs. FPDs were fabricated according to the manufacturer's instructions. A scanning microscope (JSM-6400, JEOL) with a magnification of 1,000x was used for measurements. Three-way analysis of variance showed significant differences (P < .001) in marginal adaptation between the ceramic groups. Procera Bridge Zirconia showed the lowest discrepancies (26 +/- 19 microm). No significant differences were observed between abutments and surfaces, and no significant interaction was observed among the ceramic system, abutments, and surfaces. The accuracy of fit achieved by both zirconia systems was within the range of clinical acceptability, with Procera Bridge Zirconia showing the best marginal fit.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Marginal fit of anterior 3-unit fixed partial zirconia restorations using different CAD/CAM systems

PURPOSE Few studies have investigated the marginal accuracy of 3-unit zirconia fixed partial dentures (FPDs) fabricated by computer-aided design/computer-aided manufacturing (CAD/CAM) system. The purpose of this study was to compare the marginal fit of zirconia FPDs made using two CAD/CAM systems with that of metal-ceramic FPDs. MATERIALS AND METHODS Artificial resin maxillary central and lat...

متن کامل

Effect of span length on the fit of zirconia framework fabricated using CAD/CAM system

PURPOSE The purpose of this study was to evaluate the effect of the span length on the fit of zirconia framework fabricated using CAD/CAM system. MATERIALS AND METHODS Abutments for single, 4-unit and 6-unit fixed partial prostheses were fabricated. Ten zirconia frameworks were fabricated for each group. The marginal and internal gap were presented by means of replica technique and measured b...

متن کامل

Clinical gap changes after porcelain firing cycles of zirconia fixed dentures

PURPOSE The aim of this study was to measure the changes on the marginal and internal adaptation of zirconia based anterior fixed partial dentures after the porcelain firing process. MATERIALS AND METHODS A total of 34 anterior fixed partial dentures using LAVA CAD/CAM system (3M ESPE, Germany) were applied. Two silicone replicas were obtained: one is obtained before porcelain firing process ...

متن کامل

Marginal Integrity of CAD/CAM Fixed Partial Dentures

OBJECTIVES Computer-aided design (CAD) and manufacturing (CAM) allows the milling of high strength zirconia fixed partial dentures (FPD), however bonding to an inert ZrO(2) ceramic surface may effect the marginal integrity of the FPDs. The aim of this investigation was to evaluate the marginal adaptation of zirconia FPDs at the interfaces between zirconia, cement, and tooth. METHODS 32 3-unit...

متن کامل

Evaluation of the adaptation of zirconia-based fixed partial dentures using micro-CT technology.

The objective of the study was to measure the marginal and internal fit of zirconia-based all-ceramic three-unit fixed partial dentures (FPDs) (Y-TZP - LAVA, 3M-ESPE), using a novel methodology based on micro-computed tomography (micro-CT) technology. Stainless steel models of prepared abutments were fabricated to design FPDs. Ten frameworks were produced with 9 mm2 connector cross-sections usi...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:
  • The International journal of prosthodontics

دوره 21 5  شماره 

صفحات  -

تاریخ انتشار 2008