Characterization and propagation of acoustic emission signals in woody plants: towards an improved acoustic emission counter

نویسنده

  • J. S. SPERRY
چکیده

The physics of ultrasonic acoustic emissions ( A E s ) was investigated for AE transmission through w o o d and transducers. The physical properties measured were velocity, attenuation and frequeney composition ol" AEs produced by two sources: cavitation events in xylem and peticil lead breaks. T h e authors also measured the relative sensitivity of var ious combinations of ultrasound transducets and ampliflers to aid in the selection of a measuring system optitnized for cavitation detection iti woody plan ts . Some of the authois' conclusions are; (1) Softwoods {Thuja, Pinus) attenuate AEs more rapidly t h a n hardwoods (maple, birch), (2) The velocity of A E s in wood exceeds that tneasured by others in w a t e r so the main medium of AE transmission tnust be the cellulose, (3) The strongest frequencies of AEs are in the range of 100-300 kHz, (4) Cavitationinduced AEs tend to shift to higher frequency as w o o d dehydration progtesses. (5) One cannot determine the locus of origin of AEs from its frequency cotnposition, (6) The frequency composition of the acoustic emissions probably canno t be determined at all with the sensors used because of their tendency to 'ring'. The data collected in this paper were used to aid in the design of an improved AE counter having a seven-fold increase in signal to noise ratio compared to counters previously used in our laboratory. The improved counter, tnodel 4615 Drought Stress Monitot, is now cotntnetcially available frotn Physical Acoustics Corp,, Princeton, N J , U,S,A, Key-words: acoustic emission; xylem cavitation; .icer saeehaiimi: Thuja oecidentalis: Pitius strobus.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Cluster Analysis of Acoustic Emission Signals for Carbon/Epoxy Composite in Four-point Bending Test (RESEARCH NOTE)

Due to the extensive use of composites in various industries and the fact that defects reduce ultimate strength and efficiency during operation, detection of failures in composite parts is very important. The aim of this paper is to use Acoustic Emission (AE) non-destructive method in four-point bending test of carbon/epoxy composite to analyze and examine the failure mechanisms. This method is...

متن کامل

Study of the Frictional Surface Damage Using Acoustic Emission Method

In this study, the change at rubbing surfaces has been investigated experimentally using an acoustic emission signal monitoring system. A steel ring is slipped on the surface of  a metallic sheet to simulate frictional conditions. The mechanical disturbances caused by the movement of the ring produce stress waves propagating along the sheet surface. The out of plane displacement of the sheet su...

متن کامل

Health Monitoring for Composite under Low-Cycle Cyclic Loading, Considering Effects of Acoustic Emission Sensor Type

Composites have been widely used in the aerospace industry. Due to the requirement of a high safety for such structures, they could be considered for health monitoring. The acoustic emission approach is one of most effective methods for identifying damages in composites. In this article, standard specimens were made from carbon fibers and the epoxy resin, with the [03/902/...

متن کامل

On the Use of Acoustic Emission and Digital Image Correlation for Welded Joints Damage Characterization

A series of tests have been conducted to investigate fatigue damage characterization in corroded welded steel plates using structural health monitoring (SHM) techniques. Acoustic Emission (AE) is a non-destructive testing (NDT) technique with potential applications for locating and monitoring fatigue cracks in service. In the present work, AE is implemented to characterize damage during crack e...

متن کامل

Flexural monitoring of carbon fiber/epoxy composite by acoustic emission

Carbon / epoxy composite is one of the most useful polymer matrix composites that has special properties such as high strength-to-weight ratio, high hardness, high corrosion resistance, Resistance to nuclear radiation has high consumption in different industries such as aerospace industry. Therefor monitoring of loading of this type of composite is important. In order to determine failure mecha...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2005