Low-Temperature Fabrication of Germanium-on-Insulator Using Remote Plasma Activation Bonding and Hydrogen Exfoliation

نویسندگان

  • C. A. Colinge
  • K. Y. Byun
  • I. P. Ferain
  • R. Yu
چکیده

Low-temperature germanium to silicon wafer bonding was demonstrated by in situ radical activation and bonding in vacuum. After low temperature direct bonding of Ge to Si followed by annealing at 200 and 300 C, advanced imaging techniques were used to characterize the bonded interface. The feasibility of transferring hydrogen-implanted germanium to silicon with a reduced thermal budget is also demonstrated. Germanium samples were implanted with hydrogen and a two-step anneal was performed. The first anneal performed at low temperature (B150 C for 22 h) to enhance the nucleation of hydrogen platelets. The second anneal is performed at 300 C for 5 min and is shown to complete the exfoliation process by triggering the formation of extended platelets.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Low temperature formation Silver-Copper alloy nanoparticles using hydrogen plasma treatment for fabrication of humidity sensor

In this paper, a novel method of producing bi-metallic alloy nanoparticles at low temperatures using hydrogen bombardment of thin films, deposited on glass substrates, is introduced. Optical and morphological characteristics of the nanoparticles were extensively studied for various conditions of plasma treatment, such as plasma power density, temperature, duration of hydrogen bombardment, thick...

متن کامل

Low temperature formation Silver-Copper alloy nanoparticles using hydrogen plasma treatment for fabrication of humidity sensor

In this paper, a novel method of producing bi-metallic alloy nanoparticles at low temperatures using hydrogen bombardment of thin films, deposited on glass substrates, is introduced. Optical and morphological characteristics of the nanoparticles were extensively studied for various conditions of plasma treatment, such as plasma power density, temperature, duration of hydrogen bombardment, thick...

متن کامل

Direct wafer bonding for MEMS and microelectronics

Direct wafer bonding is a method for fabricating advanced substrates for microelectromechanical systems (MEMS) and integrated circuits (IC). The most typical example of such an advanced substrate is the silicon-on-insulator (SOI) wafer. SOI wafers offer many advantages over conventional silicon wafers. In IC technology, the switching speed of circuits fabricated on SOI is increased by 20-50% co...

متن کامل

A new low-temperature high-aspect-ratio MEMS process using plasma activated wafer bonding

This paper presents the development and characterization of a new high-aspect-ratio MEMS process. The silicon-on-silicon (SOS) process utilizes dielectric barrier discharge surface activated low-temperature wafer bonding and deep reactive ion etching to achieve a high aspect ratio (feature width reduction-to-depth ratio of 1:31), while allowing for the fabrication of devices with a very high an...

متن کامل

The Effects of Damage on Hydrogen-Implant-Induced Thin-Film Separation from Bulk Silicon Carbide

Exfoliation of SiC by hydrogen implantation and subsequent annealing forms the basis for a thi n-fiim separation process ~vhichqwhen combined with hydrophilic wafer bonding. can be exploited to produce siIicon-carbide-cm-insulator, SiCOI. Sic thin films produced by this process exhibit unacceptably high resistivity because defects generated by the implant neutralize electrical carriers. Separat...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2017