Tuning Forks and Tests

ثبت نشده
چکیده

The three tuning forks generally used include : 256 Hz, 512 Hz, 1024 Hz. Most common being 512Hz. 512 because It has appropriate decay time, Less overtones and lies in speech frequency. Compressing the prongs with fingers produces around 70 dB sound and hitting against Knee or elbow 90dB. A prediction of air-bone gap can be made if tuning forks of 256, 512 and 1024 Hz are used. • Rinne test equal or negative for 256 Hz but positive for 512 Hz indicates air-bone gap of 20-30 dB. • Rinne test negative for 256 and 512 Hz but positive for 1024 Hz indicates air-bone gap of 30-45 dB. • Rinne negative for all three tuning forks, indicates air-bone gap of 45-60 dB . Remember that a negative Rinne for 256, 512 and 1024 Hz indicates a minimum AB gap of 15, 30, 45 dB respectively.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Rinne revisited: steel versus aluminum tuning forks.

OBJECTIVE (1) Determine whether tuning fork material (aluminum vs stainless steel) affects Rinne testing in the clinical assessment of conductive hearing loss (CHL). (2) Determine the relative acoustic and mechanical outputs of 512-Hz tuning forks made of aluminum and stainless steel. STUDY DESIGN Prospective, observational. SETTING Outpatient otology clinic. SUBJECTS AND METHODS Fifty su...

متن کامل

The otologist's tuning fork examination--are you striking it correctly?

OBJECTIVE To determine if the manner in which a tuning fork is activated affects its vibrational response. STUDY DESIGN Diagnostic test assessment. SETTING Hearing Center of Excellence laboratory. SUBJECTS AND METHODS A Polytec OFV-5000 scanning vibrometer was used to measure the vibrational response of 256-Hz, 512-Hz, and 1024-Hz tuning forks after activation. The tuning forks were activ...

متن کامل

Piezoelectric Quartz Tuning Forks for Scanning Probe Microscopy

In this paper the application of piezoelectric quartz tuning forks in dynamic force microscopy is described. For the introduction we give a historical overview and a comparison with traditional cantilevers. In the second section the theories for tuning forks as oscillators for the dynamic force detection are introduced and in the third section the experimental implementation is described. This ...

متن کامل

The Prague historical collection of tuning forks: a surviving replica of the Koenig tonometre

Despite the copious advances in acoustic techniques and devices for measuring and displaying acoustic parameters, a steady component of a phonetician’s scientific method remains to be – to this very day – our hearing. This paper therefore focuses on a historical device shared between acoustics and auditory phonetic analysis: Rudolph Koenig’s Grand Tonometre, consisting of more than a hundred tu...

متن کامل

Acoustic Analysis of Used Tuning Forks.

OBJECTIVE In this study, we evaluated used aluminum tuning forks (TFs) for fundamental frequencies (FF), overtones, and decay times. MATERIALS AND METHODS In total, 15 used (1 C1, 11 C2, and 3 C3) and 1 unused (C2) TFs were tuned, and the recorded sound data were analyzed using the Praat sound analysis program. RESULTS It was found that FFs of the recorded sounds produced by the used C2-TFs...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2015