Effect of Dynamic Strain Aging on Isothermal (473K) Low Cycle Fatigue of Ferritic Ductile Cast Iron

نویسندگان

  • Hayato Mouri
  • Morihito Hayashi
  • Wilfried Wunderlich
چکیده

The ferritic ductile iron (FCD400) is widely used as industrial material. As regards to its high temperature application, fatigue at elevated temperature, and advanced mechanical properties has been investigated and clarified. In low cycle fatigue (LCF), the S-N curve is presented by the relation of plastic strain to the number of cycles as fatigue life, which can be predicted by the Manson-Coffinmodel. In this model, the ductile index is appointed as a material constant of 0.5 and the ductile coefficient is related directly to the so-called plastic deformation capacity of the material. Namely, the low cycle fatigue life shall be dominated by the elongation rate. Concerned with it, one of authors reported that the elongation-to-fracture is 20% at room temperature, but reduces to about 9% at 473K. This temperature is just within the range of dynamic strain ageing (DSA), which is the phenomenon of fluctuating stress due to mobile atoms in solid solution. So, in this study, strain controlled high temperature LCF-tests were carried out on ferritic cast iron at 473K in air and the result is compared with those performed at room temperature, aiming to clarify the effect of elongation or DSA on the fatigue life. Particularly, this paper mentions about DSA effect to cyclic stress and cyclic plastic strain that causes contradiction of Manson–Coffin’s model in ‘‘the plastic strain range versus number of cycles’’ and ‘‘the stress range versus number of cycles’’ between room temperature (293K) and 473K. The fatigue life time at 473K is 175 cycles lower than that at 293K for all stress levels. However, DSA phenomena did not occur at high strain in 473K cyclic fatigue test although it cannot be observed in tensile tests at 473K. Based on the Manson-Coffin rule, the parameters (Cp 1⁄4 0:09 and 421, n 1⁄4 0:65 and 0.89 at T 1⁄4 293 and 473K, respectively) for the fatigue life time prediction have been determined. [doi:10.2320/matertrans.MRA2008482]

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

A review on fatigue design of heavy section EN-GJS-400-18-LT ductile iron wind turbine castings

A comprehensive review of fatigue behavior and fatigue design of heavy section wind turbine castings made of ductile iron EN-GJS-400-18-LT is performed. Common metallurgical defects that are affecting fatigue behavior of this material were studied. Review of different researches on quantitative effect of chunky graphite and micro structure on fatigue behavior of EN-GJS-400-18-LT was perform...

متن کامل

Structural and Mechanical Characterization of Austempered Cu - Sn Ductile Iron Alloys

The effect of heat treatment and alloying elements of copper and tin on the microstructure and mechanical properties of austempered ductile cast iron alloys is investigated. The austenitizing temperature of 890°C, the isothermal transformation (austempering) temperatures of 285, 335 and 375°C, and austempering times of 15, 30, 75 and 150 minutes are studied. The alloying elements of copper and ...

متن کامل

Low Cycle Fatigue Simulation of Valve Bridge Region in Cylinder Head Based on Critical Plane Model

The reason of this study is low cycle failure of cast iron cylinder head during the E5 standard durability test. The goal of the present investigation is durability test simulation and low cycle fatigue life evaluation of cast iron cylinder head. With uncouple structural analysis, preloads, thermal and mechanical load and boundary conditions are prescribed to finite element model of the cylinde...

متن کامل

Failure Mechanisms Investigation in Thermal Barrier Coatings under Isothermal and Non-sothermal Fatigue Loadings using Design of Experiments

In this article, failure and fracture mechanisms in an aluminum alloy (which has been used in diesel internal combustion engines), with and without ceramic thermal barrier coatings, have been investigated under isothermal and non-isothermal fatigue loadings. In this research, the base material is an aluminum-silicon-magnesium alloy and the thermal barrier coating includes a metallic bond coat l...

متن کامل

A new low cycle fatigue lifetime prediction model for magnesium alloy based on modified plastic strain energy approach

Nowadays, the technology intends to use materials such as magnesium alloys due to their high strength to weight ratio in engine components. As usual, engine cylinder heads and blocks has made of various types of cast irons and aluminum alloys. However, magnesium alloys has physical and mechanical properties near to aluminum alloys and reduce the weight up to 40 percents. In this article, a new ...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2009