An in vitro investigation of microtensile bond strengths of two dentine adhesives to caries-affected dentine.

نویسندگان

  • H Sonoda
  • A Banerjee
  • M Sherriff
  • J Tagami
  • T F Watson
چکیده

OBJECTIVES To compare the micro-tensile bond strengths of two different adhesive systems (ABF (Clearfil Protect Bond), Kuraray Medical Inc., Tokyo, Japan) and Prime & Bond NT (PBNT, Dentsply, Konstanz, Germany) bonded to caries-affected dentine retained after chemo-mechanical caries removal using Carisolv gel, with that retained after excavation using conventional hand instrumentation. METHOD Twenty, adult, human extracted carious teeth were used in this split tooth study with bur-cut cavities in sound dentine acting as controls. After clinical caries excavation, the occlusal cavities in each experimental group were restored with either bonding system plus composite. Matchstick-shaped samples through the bond interfaces were sectioned and microtensile bond strengths recorded. Scanning electron microscopy (SEM) was used to ascertain the mode of failure at the restoration-dentine interface. RESULTS Statistical analysis of the bond strength data showed that for the ABF group, there was no difference in bond strengths between the controls and Carisolv group but these values were significantly higher than those for the hand-excavated samples. PBNT samples showed no significant differences in any of the three test groups, with wider ranging data sets. SEM analysis indicated a variety of failures at the interface including cohesive failures within the caries-affected dentine itself. CONCLUSIONS From the data generated by this study it could be concluded that microtensile bond strengths of PBNT/composite restorations to caries-affected dentine in clinical cavities were statistically comparable to those to sound dentine. In the ABF/composite restored group (self-etched), the use of conventional hand excavation appeared to weaken the bond strength to the remaining caries-affected dentine. However, the use of Carisolv gel excavation did not compromise bond strengths to caries-affected dentine in either group tested.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Microtensile bond strength of total-etch and self-etching adhesives to caries-affected dentine.

OBJECTIVES To evaluate the microtensile bond strength of total-etch or self-etch adhesives to caries-affected versus normal dentine, and to correlate these bond strengths with DIAGNOdent laser fluorescence and Knoop microhardness (KH) measurements of the substrates. METHODS Extracted carious human molars were ground to expose flat surfaces where the caries lesion was surrounded by normal dent...

متن کامل

The Shear Bond Strengths of Composite Bonded to Dentine Following Treatment with Two Dentine Occluding Desensitizing Toothpastes

Aim: This study determined whether prior brushing with desensitizing toothpastes (Sensodyne Rapid Relief and Colgate Pro-Relief) affected the shear bond strengths of composite to dentine surfaces after appropriate use of two different dentine bonding agents (SingleBond and PQ-1). Materials and Methods: Sixty caries free molar teeth were cleaned, disinfected and embedded in individual cylinders ...

متن کامل

Adhesive permeability affects coupling of resin cements that utilise self-etching primers to dentine.

OBJECTIVES To examine the effects of an experimental bonding technique that reduces the permeability of the adhesive layer on the coupling of resin cements to dentine. METHODS Extracted human third molars had their mid to deep dentin surface exposed flat by transversally sectioning the crowns. Resin composite overlays were constructed and cemented to the surfaces using either Panavia F (Kurar...

متن کامل

مقایسه مواد چسبنده عاجی چند مرحله ای و تک مرحله ای در استحکام باند کامپوزیت به عاج

Composite resin restorative materials, that nowadays are used as tooth-colour materials, have both benefits and weaknesses. One of these weaknesses is the contraction resulted from resin polymerization which influences on the composite dentin bond strength and it has been tried to be eliminated by different bonding systems. The aim of this in-vitro study was to compare the dentin bond strength ...

متن کامل

Tensile bond strength of single-step self-etch adhesives to Er:YAG laser-irradiated dentin.

OBJECTIVE The purpose of this study was to evaluate the influence of Er:YAG laser irradiation on the bond strength to dentine of three single-step adhesives (AQ Bond Plus, G-Bond, and Clearfil Tri-S Bond), and one two-step self-etch adhesive (Clearfil Megabond) as a control. BACKGROUND DATA The vast majority of the numerous reports on resin bonding to Er:YAG-lased dentine have concluded that ...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:
  • Journal of dentistry

دوره 33 4  شماره 

صفحات  -

تاریخ انتشار 2005