Keeping Your Eyes Continuously on the Ball While Running for Catchable and Uncatchable Fly Balls

نویسندگان

  • Dees B. W. Postma
  • A. Rob den Otter
  • Frank T. J. M. Zaal
چکیده

When faced with a fly ball approaching along the sagittal plane, fielders need information for the control of their running to the interception location. This information could be available in the initial part of the ball trajectory, such that the interception location can be predicted from its initial conditions. Alternatively, such predictive information is not available, and running to the interception location involves continuous visual guidance. The latter type of control would predict that fielders keep looking at the approaching ball for most of its flight, whereas the former type of control would fit with looking at the ball during the early part of the ball's flight; keeping the eyes on the ball during the remainder of its trajectory would not be necessary when the interception location can be inferred from the first part of the ball trajectory. The present contribution studied visual tracking of approaching fly balls. Participants were equipped with a mobile eye tracker. They were confronted with tennis balls approaching from about 20 m, and projected in such a way that some balls were catchable and others were not. In all situations, participants almost exclusively tracked the ball with their gaze until just before the catch or until they indicated that a ball was uncatchable. This continuous tracking of the ball, even when running close to their maximum speeds, suggests that participants employed continuous visual control rather than running to an interception location known from looking at the early part of the ball flight.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

When a Fly Ball Is Out of Reach: Catchability Judgments Are Not Based on Optical Acceleration Cancelation

The optical acceleration cancelation (OAC) strategy, based on Chapman's (1968) analysis of the outfielder problem, has been the dominant account for the control of running to intercept fly balls approaching head on. According to the OAC strategy, outfielders will arrive at the interception location just in time to catch the ball when they keep optical acceleration zero. However, the affordance ...

متن کامل

The information for catching fly balls: judging and intercepting virtual balls in a CAVE.

Visually guided action implies the existence of information as well as a control law relating that information to movement. For ball catching, the Chapman Strategy--keeping constant the rate of change of the tangent of the elevation angle (d(tan(alpha))/dt)--leads a catcher to the right location at the right time to intercept a fly ball. Previous studies showed the ability to detect the informa...

متن کامل

Numerical and Experimental Evaluation of Residual Stress and Fatigue Strength of Steel CK35 in Shot Peening Process

In shot peening process the work piece surface is struck by a large number of balls and compressive residual stress is generated on the surface. So, mechanical properties such as fatigue strength, stress corrosion resistance, smooth shape and ... will improve. In this paper, the balls with a speed of 100 to 200 m/s were struck on the steel samples and fatigue strength compared with specimens wi...

متن کامل

An investigation of the corrosive wear of steel balls in grinding of sulphide ores

Ball mills are common grinding equipment in mineral processing industries. Ball wear results from three mechanisms namely impact, abrasion and corrosion. Of these, the corrosion mechanism is the least investigated, due to its chemical-electrochemical nature. Therefore, the aims of this research were to investigate the grinding chemistry influence (slurry pH, solid percentage, water chemistry an...

متن کامل

MODELING AND OPTIMIZING THE CORROSIVE WEAR OF STEEL BALLS IN BALL GRINDING MILL

This paper was aimed to address the modeling and optimization of factors affecting the corrosive wear of low alloy and high carbon chromium steel balls. Response surface methodology, central composite design (CCD) was employed to assess the main and interactive effects of the parameters and also to model and minimize the corrosive wear of the steels. The second-order polynomial regression model...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره 9  شماره 

صفحات  -

تاریخ انتشار 2014