Nanoleakage Phenomenon on Deproteinized Human Dentin

نویسندگان

  • Patrícia de Britto Pereira Garcia Duarte
  • Eduardo Moreira da Silva
چکیده

OBJECTIVE The purpose of this study was to evaluate the influence of dentin deproteinization on the nanoleakage phenomenon. MATERIAL AND METHODS Class V cavities were prepared in 12 human molars with cervical margins located in dentin. The cavities were assigned to 2 groups (n=6) according to dentin treatment: Group I - dentin treated in accordance with the manufacturer's instructions and Group II - dentin treated following the manufacturer's instructions + 10% NaOCl. Each group was sub-divided into three groups, according to the DBS (dentin bonding system) used: Scotchbond Multi Purpose (SBMP), Prime & Bond NT (PB) and Clearfil SE Bond (SE), which were applied according to manufacturer's instructions. The cavities were restored with composite resin, and the specimens were immersed in a tracer agent (AgNO3 50%) for 24 h. The teeth were sectioned buccolingually through the center of the restorations, and nanoleakage pattern was evaluated by scanning electron microscopy (SEM) using the backscattered electron image mode. RESULTS SEM analysis showed different nanoleakage patterns for each DBS. Irrespective of dentin treatments, all SBMP specimens showed nanoleakage. SE did not show any nanoleakage with both dentin treatments used. PB showed nanoleakage within the hybrid layer only in Group I. CONCLUSIONS The influence of dentin deproteinization on the nanoleakage phenomenon was dependent on dentin bonding system formulation and bonding strategies.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Effects of different dentin bonding agents on nanoleakage and hybrid layer thickness

Effects of different dentin bonding agents on nanoleakage and hybrid layer thickness Dr. M. Ghavamnasiri* - Dr. F. Maleknejad* - Dr. H. Ameri** - Dr. MJ. Moghadas** *- Associate Professor of Operative Dentistry Dept. – Faculty of Dentistry – Mashhad University of Medical Sciences. **- Assistant Professor of Operative Dentistry Dept. – Faculty of Dentistry – Mashhad University of Medical Science...

متن کامل

Nanoleakage and Durability of Resin/Dentin Bonds

Micromorphological analysis is a useful method for the evaluation of resin–dentin bonds. Transmission electron microscopy (TEM) can also be used to analyze the structure of resin–dentin bonds because of its high resolution. There are several reasons for the degradation of resin–dentin bonds such as the activation of endogenous dentin matrix metalloproteinases and the hydrolysis of methacrylate ...

متن کامل

Effect of water on bonding of one-bottle self-etching adhesives.

This study evaluated the effect of water on dentin substrate bonding of one-bottle self-etching adhesives. Dentin substrates were divided into two groups: wet and dry dentin. Wet dentin is the normal substrate for bond testing whereas dry dentin was dehydrated in a desiccator for 24 hours. Bonded dehydrated teeth were then divided into two subgroups: stored in water or in desiccator for 24 hour...

متن کامل

Nanoleakage of fiber posts luted with different adhesive strategies and the effect of chlorhexidine on the interface of dentin and self-adhesive cements.

The aim of this in vitro study was to evaluate the nanoleakage of fiber posts luted using different adhesive strategies and to investigate the effect of 2% chlorhexidine (CHX) on nanoleakage at the resin-dentin interfaces of self-adhesive cements. The self-adhesive and etch-and-rinse adhesive groups tested demonstrated similar results with regard to nanoleakage. Pretreatment with CHX promoted a...

متن کامل

In vitro effect of nanoleakage expression on resin-dentin bond strengths analyzed by microtensile bond test, SEM/EDX and TEM.

This study evaluated the effect of multiple consecutive adhesive resin coatings of adhesive bonded to human dentin on nanoleakage and resin-dentin bond strength. Resin bonded dentin specimens were prepared using a total-etch adhesive (One-Step Plus) applied as multiple consecutive coating, or using two self-etch adhesive systems (iBond or Fluoro Bond). For the total-etch adhesive, resin applica...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره 15  شماره 

صفحات  -

تاریخ انتشار 2007