On the Optical Properties of Blown and Cast Polyethylene Films: Surface Versus Bulk Structural Considerations
نویسنده
چکیده
In this paper we report on some surprising, and we believe new, findings regarding the factors affecting the optical properties (haze) of polyethylene (PE) blown and cast films. A comprehensive investigation of blown and cast films made from conventional Ziegler-Natta catalyzed linear low density PE (LLDPE) as well as metallocene-catalyzed LLDPE (mLLDPE) resins was conducted. The large majority of the contribution to the total haze in the blown and cast films was observed to come from the surface roughness of the films, with the bulk (internal) contribution being relatively minor. Using a variety of analysis and characterization methods, including atomic force microscopy (AFM), small angle light scattering (SALS), and wide angle x-ray scattering (WAXS), we determined that the surface roughness in these films was a result of the development of distinct spherulitic-like superstructures formed during the blown or cast film processing. Furthermore, these superstructures were observed only in the mLLDPE blown films, and not in the LLDPE blown films processed at similar conditions. Analysis of the rheological and molecular characteristics of these various mLLDPE and LLDPE resins revealed that the mLLDPE resins exhibited considerably lower molecular weight, narrower molecular weight distribution, lower zero shear viscosity, and lower melt elasticity compared to the LLDPE resins of similar melt index (MI). These observations support our general finding and primary conclusion from this work that in PE blown and cast films made using typical processing conditions, the optical haze properties are adversely affected due to enhanced surface roughness caused by the formation of spherulitic-like superstructures in polymer melts that possess fast relaxing and low melt elasticity rheological characteristics. Matthew B. Johnson Chapter VIII Optical Properties of PE Films _______________________________________________________________________ 288 8.
منابع مشابه
Substrate Effects on the Structural Properties of Thin Films of Lead Sulfide
Nanocrystalline PbS thin films are deposited on glass and alumina substratesthrough the chemical bath deposition technique by creating similar conditions, in orderto investigate the effects of the substrate. The structural and optical properties of PbSfilms are investigated by X-ray diffraction, scanning electron microscope, and UV–Vis.The structural analyses of the films indicate that they are...
متن کاملCharacterizing films of polyethylene blends: An application of colorimetric parameters measurements
This study reports an application of instrumental color measurement for quantifying and comparing the optical properties of high density polyethylene HDPE and low density polyethylene LDPE blend films and the effect of blending ratio and miscibility on these properties. The technique of spectrophotometry in transmission and reflectance modes can be used as a versatile tool to evaluate the color...
متن کاملInvestigation of Structural, Morphological and Optical Properties of Chromium Oxide Thin Films Prepared at Different Annealing Times
Chromium oxide (α-Cr2O3) thin films were prepared using thermal annealing of chromium (Cr)films deposited on quartz substrates by direct current (DC) magnetron sputtering. The annealingprocess of the films was performed for different times of 60, 120,180 and 240 min. The influenceof annealing time on structural, morphological and optical properties of the prepared films wasinvestigated by diffe...
متن کاملStudy of Composition and Optical Properties of Chemically Deposited Pd-xSb2S3 Thin Films
The study reports on the effects of different concentration of palladium impurities on the compositional and optical properties of Palladium Doped Antimony Sulphide (Pd-xSb2S3) thin films grown by the chemical bath deposition method. The films were grown at room temperature and other deposition conditions such as the bath temperature, pH, complexing agents were kept constant. The concentration ...
متن کاملFabrication Of Cu(In,Ga)Se2 Solar Cells With In2S3 Buffer Layer By Two Stage Process
Cu(In,Ga)Se2 thin films (CIGS) on metallic substrate (titanium, molybdenum, aluminum, stainless steel) were prepared by a two-step selenization of Co-evaporated metallic precursors in Se-containing environment under N2 gas flow. Structural properties of prepared thin film were studied. To characterize the optical quality and intrinsic defect nature low-temperature photoluminescence, were perfor...
متن کامل