The effects of X-ray photoionization and heating on the structure of circumstellar discs

نویسندگان

  • R. D. Alexander
  • C. J. Clarke
  • J. E. Pringle
چکیده

We present the results of a theoretical study investigating the effects of photoionization and heating by X-rays on discs around low-mass stars. In particular we address the question of whether or not X-rays can drive a disc wind. First, we construct a 1-dimensional “quasi-hydrostatic” model, which solves for the vertical structure introduced by X-ray heating. We consider uniform X-ray illumination of the disc, but the X-ray fluxes required to heat the disc significantly are much greater than those seen by recent observations. When the model is extended to consider heating from a central X-ray source we find that the 1-dimensional model is only valid very close to the star. We extend our analysis to consider a simple 2-dimensional model, treating the disc as a two-layered structure and solving for its density profile self-consistently. For T Tauri stars we are able to set a crude upper limit on the mass-loss rate that can be driven by X-ray photoevaporation, with a value of ≃ 10g cm s. Our model is designed to maximise this value, and most likely over-estimates it significantly. However we still find a mass-loss rate which is less than that found in studies of ultraviolet photoevaporation. We conclude that in the presence of a significant UV field, X-ray driven disc winds are unlikely to play a significant role in the evolution of discs around low-mass stars.

برای دانلود رایگان متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Effect of Joule-Heating Annealing on Giant Magnetoimpedance of Co64Fe4Ni2B19-xSi8Cr3Alx (x = 0, 1 and 2) Melt-Spun Ribbons

In this work, we have studied the influence of dc joule-heating thermal processing on the structure, magnetoimpedance (MI) and thermal properties of Co64Fe4Ni2B19-xSi8Cr3Alx (x = 0, 1, and 2) rapidly solidified melt-spun ribbons. The nanocrystallization process was carried out by the current annealing of as-spun samples at various current densities. As-spun and joule-heated samples were studied...

متن کامل

Effect of various fuels on structure and photo-catalytic activity of TiO2 nano-crystalline prepared by microwave-assisted combustion method

Nano-crystalline TiO2 were synthesized by combustion method using metal nitrate solution and urea, glycin and citric acid fuels. Microwave irradiation was used as heating source. X-ray diffraction, scanning electron microscope as well as Fourier transform infrared spectroscopy were performed to characterize the obtained samples. X-ray diffraction patterns revealed that in the case of citric aci...

متن کامل

Effect of heating rate on morphological features of oxidized electrolessnickel–boron coatings

Due to the high hardness and wear resistance, electroless nickel-boron (Ni-B) coatings have found numerous applications. In the present study, the influence of the heating rate on the morphological features of oxidized electroless Ni-B coatings was investigated. The oxidation behavior of electroless coating layers was studied with TGA method under non-isothermal conditions at heating rates 5, 9...

متن کامل

The Influence of Heat-Input on Structural and Mechanical Properties of 2205 Duplex Stainless Steel

The influence of heat-input and pre-heat treatment on the structure, mechanical and corrosion behaviors of 2205 duplex stainless steel joint by means of GMAW process was the goal of this study. In this regards, the welding process was done using different heat input in the range of 0.6 to 1.4 kJ/mm and different pre-heating treatments in the range of 25 to 100 oC. The microstructural properties...

متن کامل

The Influence of Heat-Input on Structural and Mechanical Properties of 2205 Duplex Stainless Steel

The influence of heat-input and pre-heat treatment on the structure, mechanical and corrosion behaviors of 2205 duplex stainless steel joint by means of GMAW process was the goal of this study. In this regards, the welding process was done using different heat input in the range of 0.6 to 1.4 kJ/mm and different pre-heating treatments in the range of 25 to 100 oC. The microstructural properties...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2008