Development of Novel Semisolid Powder Processing for Micromanufacturing

نویسنده

  • Yufeng Wu
چکیده

Semisolid powder processing (SPP) is a promising approach for near net-shape forming of features in micro/meso-scale. By combining the concept of forming in the semisolid state and conventional powder metallurgy, SPP provides a novel solution to various processing and materials engineering challenges faced in micromanufacturing. Replacing bulk materials with powdered materials adds a new dimension to the traditional semisolid technique by allowing tailoring of material properties. In this dissertation, experimental study to understand flow characteristics of metallic powders in the semisolid state is performed, and its potential application to the fabrication of a functionally graded structure (FGS) is demonstrated. The viscosity and phase segregation behavior of Al-Si powders in the semisolid state were first studied with back extrusion experiments. Effects of process parameters including shear rate, extrusion ratio, heating time and pre-compaction pressure were analyzed using the design of experiments method. The results showed that the effects of shear rate, extrusion ratio and heating time were statistically significant factors influencing the viscosity. The semisolid state powders showed a shear thinning behavior. Moreover, microstructure analysis of extruded parts indicated severe phase segregation during the forming process. As the extrusion opening became small (~400 μm), the phase segregation increased. A two-layer FGS with one layer reinforced by SiC particles was fabricated with SPP. The results indicate that SPP is capable of fabricating graded structures with promising microstructures and mechanical properties. When the SiC particles are larger than the matrix

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Hydrothermal Assisted Sol-Gel Process on Binary Mixtures of Aluminum and Titanium Alkoxides: A Novel Route for the Fabrication of Single Phase Tialite

Combination of sol-gel and hydrothermal routes in the metal alkoxide binary system of Al(OR)3-Ti(OR)4 (R= -CH(CH3)2 or -CH2CH2OCH3) were investigated to prepare single phase aluminum titanate (tialite). The effects of various parameters, such as hydrothermal processing temperature, solvent polarity and the type of alkoxide precursor, in phase development of the product powders have been investi...

متن کامل

Optimization and utilization of semisolid casting process for semisolid welding of Al-6061 alloy

Semisolid processing is one of the modern routes in sound and near net shape parts production.  Preparation of semisolid slurry using a cooling slope is increasingly becoming popular, primarily because of its simplicity in design and ease of control of the process. In this research, the microstructures of Al6061 semisolid alloy cast via a miniature cooling slope were investigated. The propertie...

متن کامل

Research on Semisolid Microstructural Evolution of 2024 Aluminum Alloy Prepared by Powder Thixoforming

A novel method, powder thixoforming, for net-shape forming of the particle-reinforced Aluminum matrix composites in semi-solid state has been proposed based on powder metallurgy combining with thixoforming technology. The microstructural evolution and phase transformations have been investigated during partial remelting of the 2024 bulk alloy, prepared by cold pressing of atomized alloy powders...

متن کامل

NEURAL NETWORK MODELING OF THE EFFECT OF COOLING SLOPE CASTING PARAMETERS ON PARTICLE SIZE OF PRIMARY SILICON CRYSTALS OF SEMISOLID CAST INGOTS OF Al-20Si (wt%)

Abstract: Cooling slope-casting processing is a relatively new technique to produce semisolid cast feedstock for the thixoforming process. Simple equipment, ease of operation, and low processing costs are the main advantages of this process in comparison with existing processes such as mechanical stirring, electromagnetic stirring, etc. The processing parameters of cooling slope casting are...

متن کامل

NEURAL NETWORK PREDICTION OF THE EFFECT OF SEMISOLID METAL (SSM) PROCESSING PARAMETERS ON PARTICLE SIZE AND SHAPE FACTOR OF PRIMARY α-Al ALUMINUM ALLOY A356.0.

Abstract: Problems such as the difficulty of the selection of processing parameters and the large quantity of experimental work exist in the morphological evolutions of Semisolid Metal (SSM) processing. In order to deal with these existing problems, and to identify the effect of the processing parameters, (i.e. shearing rate-time-temperature) combinations on particle size and shape factor, ...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2015