In situ Observation of Phase Transformation in MnAl(C) Magnetic Materials
نویسندگان
چکیده
The phase transformation in two modes, including both displacive and massive growth of τ-phase from ε-MnAl(C), was observed by in situ transmission electron microscopy. The exact temperature range for different phase transformation modes was determined by magnetic measurements. The displacive growth of ε→τ in Mn54Al46 (or Mn54Al46C2.44) occurs at temperatures below 650 K (or 766 K), above which both modes coexist. One-third or less of the ε-phase can be transformed into τ-phase via displacive mode while the remaining two-thirds or more via massive mode. In bulk τ-phase, most τ-nanocrystals formed via displacive mode are distributed in the matrix of large τ-grains that formed via massive mode. The typical massive growth rate of the τ-phase is 8-60 nm/s, while the displacive growth rate is low. A more complete understanding of the ε→τ phase transformations in the MnAl-based magnets was provided in this work, based on which the annealing process for ε→τ was optimized and thus high purity τ-phase with high saturation magnetization was obtained.
منابع مشابه
Magnetism-Structure Correlations during the ε→τ Transformation in Rapidly-Solidified MnAl Nanostructured Alloys
Magnetic and structural aspects of the annealing-induced transformation of rapidly-solidified Mn55Al45 ribbons from the as-quenched metastable antiferromagnetic (AF) ε-phase to the target ferromagnetic (FM) L10 τ-phase are investigated. The as-solidified material exhibits a majority hexagonal ε-MnAl phase revealing a large exchange bias shift below a magnetic blocking temperature TB~95 K (Hex~1...
متن کاملBeneficiation of Low-Grade Laterite Nickel by Calcination-Magnetic Separation Method
In this research, Effect of thermal treatment on beneficiation of low-grade laterite nickel by calcination-magnetic separation method was studied. In order to determine the components and elements of the sample, to recognize the main and minor minerals and their bond, and phase transformation caused by thermal treatment, Chemical analysis (XRF and ICP), microscopic studies and XRD analysis ...
متن کاملبررسی پارامترهای ساخت کامپوزیت مولایت- آلومینا- کاربیدسیلیسیم بهروش درجا توسط احیای کربوترمیک مواد آلومینوسیلیکاتی
Mullite and alumina are common in high-temperature applications because of their low thermal expansion coefficient and good thermal shock resistance. Evolution of SiC in the matrix and using it as reinforcing phase can improve thermo-mechanical properties of these materials. Also, in-situ formation of the reinforcing phases by using inorganic materials is an economical process. In this work, cr...
متن کاملInfluence of aging temperature on phase transformation and mechanical behavior of NiTi thin films deposited by magnetron sputtering technique
In this study, NiTi thin films were deposited on the glass and NaCl substrates by means of magnetron sputtering method. The influence of aging temperature, over the range 300-500 oC, on phase transformation and mechanical properties of the sputtered NiTi thin films were studied by differential scanning calorimetry (DSC) and nano-indentation assay, respectively. The DSC curves showed that the ag...
متن کاملThe effect of nano transition metals on microstructure and phase evolution of low carbon MgO-C refractories
In the present study, the effect of Iron Nitrate as catalytic precursor to in situ formation of nano-Fe particles in phenolic resin and microstructural evolution of MgO-C refractories has been investigated. Therefore, various samples according to matrix section formulation of low carbon MgO-C refractories (LCMCR’s) with 0 and 6 wt% (Fe/Phenolic resin) were prepared and phase and microstructure ...
متن کامل