Effects of sulfur-based hemostatic agents and gingival retraction cords handled with latex gloves on the polymerization of polyvinyl siloxane impression materials

نویسندگان

  • Carlos Eduardo Palhares MACHADO
  • Carlos Gramani GUEDES
چکیده

OBJECTIVES This study investigated the possible interactions between three addition silicone materials (Express®, Aquasil Ultra® and Adsil®), three hemostatic agents (ferric sulfate, StatGel FS®; aluminum sulfate, GelCord®; and aluminum chloride, Hemostop®) and gingival retraction cords previously handled with latex gloves to determine whether direct contact with medicaments or indirect contamination by latex in conditions similar to those found in clinical practice inhibit or affect the setting of the impression materials. MATERIAL AND METHODS A portable device for the simultaneous test of several specimens was specifically developed for this study. Polymerization inhibition was analyzed by examination of the impressions and the molded surface. Ten trials were performed for each addition silicone material used in the study, at a total of 240 study samples. RESULTS All the samples tested (N=240) were nonreactive regardless of the type of combination used. CONCLUSIONS Aluminum sulfate, ferric sulfate and aluminum chloride hemostatic solutions did not show any inhibitory potential on the addition silicone samples under study, and there were no changes in polymerization as a result of contact between addition silicone and retraction cords handled with latex gloves.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Comparison of the effect of different medicaments on surface reproduction of two commercially available Polyvinyl Siloxane impression materials - An Invitro Study

OBJECTIVE To determine the effect of different retraction cord medicaments on surface detail reproduction of polyvinyl siloxane impression materials and compare this effect on any two brands of commercially available polyvinyl siloxane impression materials. MATERIAL AND METHODS Four stainless steel dies were made according to ADA specification no.19. Three dies were treated with aluminium chl...

متن کامل

Hydraulic and hydrophobic impressions.

One of the most frustrating aspects of making final impressions for crowns and bridges involves the management of finish lines that extend subgingivally. The dentist must contend with many problems like relapsing gingival tissue which can obstruct the flow of impression material into the sulcus. This is most often managed by packing retraction cord which is time-consuming, difficult and often u...

متن کامل

Dimensional Accuracy of Polyvinyl Siloxane Impression Materials Considering Impression Techniques– A Literature Review

Objectives Impression accuracy is the main determinant of the fit, form and function of prosthetic restorations. Polyvinyl siloxane (PVS) is the material of choice in most clinical situations. The purpose of this paper is to provide an up-to-date review of scientific articles which discuss the dimensional accuracy of PVS impression material using various impression techniques, tray types and sp...

متن کامل

Effect of Conventional and Experimental Gingival Retraction Solutions on the Tensile Strength and Inhibition of Polymerization of Four Types of Impression Materials

In the present study, two types of tests (tensile strength test and polymerization inhibition test) were performed to evaluate the physical and chemical properties of four impression materials [a polysulfide (Permlastic), a polyether (Impregum), a condensation silicone (Xantopren) and a polyvinylsiloxane (Aquasil)] when polymerized in contact with of one conventional (Hemostop) and two experime...

متن کامل

Glove over glove technique for manipulation of vinyl polysiloxane impression material with latex gloves

Despite prior recommendations for removal, latex gloves remain prevalent in dental clinical practice because of puncture resistance, durability, and user satisfaction.[1] However, latex gloves can impair polymerization of vinyl polysiloxane impression material (VPS) thus, resulting in inaccurate and distorted impressions, which may require the clinician to repeat the impression procedure leadin...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره 19  شماره 

صفحات  -

تاریخ انتشار 2011