Unsymmetric Wrinkling of Circular Plates

نویسنده

  • EDWARD L. REISS
چکیده

The branching of un,symmetric equilibrium states from axisymmetric equilibrium states for clamped circular plates subjected to a uniform edge thrust and a uniform lateral pressure is analyzed in this paper. The branching process is called wrinkling and the loads at which branching occurs are called wrinkling loads. The nonlinear von Karman plate theory is employed. The wrinkling loads are determined by solving numerically the eigenvalue problem obtained by linearizing about a symmetric equilibrium state. The post-wrinkling behavior is studied by a perturbation expansion in the neighborhood of the wrinkling loads.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

A CLOSED-FORM NON- LINEAR SOLUTION FOR PLASTIC FLANGE WRINKLING OF CIRCULAR PLATES IN DEEP DRAWING PROCESS

This paper deals with two-dimensional plane stress wrinkling model of a plastic annular plate. Based on energy method and the nonlinearity of strain-displacement law, a bifurcation function in polar coordinates is derived analytically. This technique leads to the critical conditions for the onset of the plastic wrinkling of flange during the deep drawing process. To find this solution, the Tres...

متن کامل

A Closed-form Semi-analytical Elastic-Plastic Solution for Predicting the Onset of Flange Wrinkling in Deep-drawing of a Two-layered Circular Plate

In this paper to predict the critical conditions for onset of elastic-plastic wrinkling of flange of a two-layered circular blank during the deep-drawing process a closed-form semi-analytical elastic-plastic solution using Tresca yield criterion alongwith deformation theory in plasticity with considernig the perfectly plastic behaviour of materials is presented. Simplifying the presented soluti...

متن کامل

Pii: 0045-7949(89)90035-7

Based on the adaptive Dynamic Relaxation (aDR) method, a modified adaptive Dynamic Relaxation (maDR) method is proposed which is more efficient than the former in solving non-linear problems. It is then applied to analysing the elastic-plastic bending of circular plates in large deflection and their following wrinkling, and leads to satisfactory results compared with corresponding experimental ...

متن کامل

Analysis of pressure distribution and optimization of working conditions during push bending of circular tubes

Thin-walled tube bending is still to be considered a new and advanced technique. The process has been adopted into several industries such as aero and automotive. This process may produce a wrinkling, bulking and tearing phenomenon if the process parameters are inappropriate, especially for tubes with large diameter and thin wall thickness. Push bending process is one of the methods used for be...

متن کامل

Load Carrying Capacity of Simply Supported Variable Thickness Circular Plates

The calculation of the load carrying capacity of variable thickness circular plates subjected to arbitrary rotational symmetric loading is presented. The analysis considers plate materials that obey either the square or the Tresca yield criterion. By using upper and lower bound theorems of limit analysis, corresponding estimations for the load carrying capacity of the plate are obtained. It is ...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2016