Experimental Investigations on Subsequent Yield Surface of Pure Copper by Single-Sample and Multi-Sample Methods under Various Pre-Deformation

نویسندگان

  • Gui-Long Liu
  • Shi-Hong Huang
  • Che-Si Shi
  • Bin Zeng
  • Ke-Shi Zhang
  • Xian-Ci Zhong
چکیده

Using copper thin-walled tubular specimens, the subsequent yield surfaces under pre-tension, pre-torsion and pre-combined tension-torsion are measured, where the single-sample and multi-sample methods are applied respectively to determine the yield stresses at specified offset strain. The rule and characteristics of the evolution of the subsequent yield surface are investigated. Under the conditions of different pre-strains, the influence of test point number, test sequence and specified offset strain on the measurement of subsequent yield surface and the concave phenomenon for measured yield surface are studied. Moreover, the feasibility and validity of the two methods are compared. The main conclusions are drawn as follows: (1) For the single or multi-sample method, the measured subsequent yield surfaces are remarkably different from cylindrical yield surfaces proposed by the classical plasticity theory; (2) there are apparent differences between the test results from the two kinds of methods: the multi-sample method is not influenced by the number of test points, test order and the cumulative effect of residual plastic strain resulting from the other test point, while those are very influential in the single-sample method; and (3) the measured subsequent yield surface may appear concave, which can be transformed to convex for single-sample method by changing the test sequence. However, for the multiple-sample method, the concave phenomenon will disappear when a larger offset strain is specified.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Experimental investigations on a pre-chamber spark plug with variable heat range by integrating a controlled hot surface

In gasoline engines, pre-chamber spark ignition systems are used to achieve high efficiency and low NOx emissions when operating under lean conditions. While a cold pre-chamber spark plug can lead to misfiring and flame quenching under cold start or part load operation, a hot pre-chamber can result in uncontrolled pre-ignition phenomena under full load operation. This paper presents an approach...

متن کامل

Electroanalytical sensing of Asulam based on nanocomposite modified glassy carbon electrode

In this study a facile approach to employ Copper nanoparticle (CuNPs) and multi-walled carbon nanotubes (MWCNT) as the nanomaterial for selective detection of asulam have been investigated. This work reports the electrocatalytic oxidation of asulam on glassy carbon electrodes (GCE) modified with multi-walled carbon nanotubes (MWCNT), ionic liquids (IL), chitosan (Chit) and copper nanoparticles ...

متن کامل

Simulation of deformation behavior of porous Titanium using Modified Gurson yield function

In this research the stress-strain curve of porous Titanium, as a common material for biomedical application, was predicted using the mechanical properties of fully solid Titanium experimental data. Modified Gurson model (Gurson-Tvergaard-Needleman (GTN) model) was used to predict the plastic response of porous Titanium in compaction. Different values of GTN parameters were used for different i...

متن کامل

Experimental Study on Double-Walled Copper and Carbon/Epoxy Composite Tubes under the Axial Loading

This paper investigates axial compression process of multi-layered tubes with circular cross-section under the axial loading in the quasi-static condition using experimental method. Some specimens are prepared in seven different groups, namely; empty carbon/epoxy composite tubes, solid carbon/epoxy composite rods, empty copper tubes, composite tubes with silicon sealant filler, concentrically s...

متن کامل

Modeling and Experimental Study of Static Recovery and Mechanical Behavior of AA5052 Alloy During Cold-Working and Subsequent Annealing

In the present study, the mechanical behavior of AA5052 aluminum alloy during cold deformation and subsequent isothermal annealing in a temperature range of 225-300oC was investigated using the uniaxial tensile test data. It is found that by increasing the annealing time and temperature the material yield strength is decreased. The microstructural investigations of the annealed samples show tha...

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره 11  شماره 

صفحات  -

تاریخ انتشار 2018