Tailoring the Wettability of Carbon Nanotube Powders, Bucky Papers and Vertically Aligned Nanofibers by Plasma Assisted Functionalization
نویسندگان
چکیده
Within the DESYGN-IT research project, funded by the European Commission, carbon nanotubes (CNT) were investigated in the form of powder, vertically grown on a Si substrate and as CNT sheets or mats, mostly referred as to "bucky paper". Due to their hydrophobic and inert nature, functionalization or alteration of nanotubes can be necessary to optimize them for desired applications. The low pressure glow discharge treatment was investigated in terms of their ability to increase the wettability of bucky papers produced from multi walled carbon nanotubes (MWNT) powders. Hydrophilized bucky papers are required for their use as Volume 3 | November 2007 Page 1 of 12 DOI: 10.2240/azojono0126 Uwe Vohrer, Justin Holmes, Zhonglai Li, AunShih Teh, Pagona Papakonstantinou, Manuel Ruether and Werner Blau actuators in an electrolyte solution or a substrate for cell cultures. The opening of end caps of aligned grown CNTs based on plasma treatment was a second aim. The as-produced carbon nanotube materials (powder, bucky paper, aligned structures) as well as the plasma treated samples were characterized by surface analytical techniques like SEM, ESCA, TGA, BET to find optimized parameter sets. By using oxygen containing plasmas, the increase in wettability of CNT mats could be successfully shown. Plasma polymerisation of a carbofluorine monomer onto a bucky paper leads to superhydrophobic surfaces. We found that under gentle oxidation parameters the vertical alignment of MWNTs remains unchanged whereas more harsh conditions destroy the CNT shape without opening the end caps.
منابع مشابه
Laser-assisted simultaneous transfer and patterning of vertically aligned carbon nanotube arrays on polymer substrates for flexible devices.
We demonstrate a laser-assisted dry transfer technique for assembling patterns of vertically aligned carbon nanotube arrays on a flexible polymeric substrate. A laser beam is applied to the interface of a nanotube array and a polycarbonate sheet in contact with one another. The absorbed laser heat promotes nanotube adhesion to the polymer in the irradiated regions and enables selective pattern ...
متن کاملOptimized Conditions for Catalytic Chemical Vapor Deposition of Vertically Aligned Carbon Nanotubes
Here, we have synthesized vertically aligned carbon nanotubes (VA-CNTs), using chemical vapor deposition (CVD) method. Cobalt and ethanol are used as the catalyst and the carbon source, respectively. The effects of ethanol flow rate, thickness of Co catalyst film, and growth time on the properties of the carbon nanotube growth are investigated. The results show that the flow rate of ethanol and...
متن کاملBiofouling Behavior on Forward Osmosis Using Vertically Aligned CNT Membrane on Alumina
Nowadays, forward osmosis (FO) with many advantages in water treatment, are so attractive for researchers and investigators that the studies are going to optimize and increase its efficiency. However one of the most controversial operating malfunctions of FO process is fouling that limits the FO global application. In the following research, vertically aligned carbon nanotube (VACNT) on alumina...
متن کاملPolymer-masking for controlled functionalization of carbon nanotubes.
An effective and versatile method for tube-length-specific functionalization of carbon nanotubes through a controllable embedment of vertically-aligned carbon nanotubes into polymer matrices is reported, which allows not only asymmetric functionalization of nanotube sidewalls, but also facile introduction of new properties (e.g. magnetic) onto the region-selectively functionalized carbon nanotu...
متن کاملTailoring wettability change on aligned and patterned carbon nanotube films for selective assembly.
The effects of oxygen reactive ion etching (RIE) on the surface wettability of aligned carbon nanotube (CNT) films have been systematically investigated. It was found that 3 s of RIE treatment could change the surface of CNT films from hydrophobic to more hydrophilic. The degree of modification in the surface wettability of the film could be controlled by the flow rate of O2 gas during the RIE ...
متن کامل