The development of a simulation model of the dense packing of large particulate assemblies

نویسندگان

  • Konstantin Sobolev
  • Adil Amirjanov
چکیده

The dense packing of particulate assemblies is an enduring theoretical and practical problem. In spite of its apparent simplicity, this problem still remains challenging. Recent progress in the performance of computers boosted the development and realization of a number of effective packing algorithms. Yet, because of the complexity of the problem, many of existing methods have difficulties in handling large numbers of particles. A simulation model is proposed to overcome this. The model assumes that the centers of the spheres are randomly generated at the intersections of a cubic lattice. The largest possible spheres are packed first; subsequent spheres are limited by the set of minimum diameters, which is specified by the constraints imposed by two major parameters imitating the compaction gradient: a reduction coefficient and the number of packing trials. Importantly, the packing arrangements are not defined by the initially specified particle size distribution (as considered by many existing packing algorithms), but rather the most dense particle size distribution, along with the corresponding value of packing degree, is generated by the proposed model. Based on these criteria, a very fast algorithm was developed for simulating of the dense packing of large assemblies of particulate, spherical material (in the order of millions of particles). Using this approach, the influence of geometrical parameters and model variables on the degree of packing and the corresponding distribution of particles was studied. D 2004 Elsevier B.V. All rights reserved.

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

منابع مشابه

Wall Effect in 3D Simulation Of Same Sized Particles Packing

In this paper, the effects of container size on the porosity of random loose packing of mono size particles have been investigated using an Event Dynamics (ED) based model. Simultaneous effects of square container walls on particles packing and their order are also investigated. Our simulation results indicate higher container size will increase the total packing factor and high density regions...

متن کامل

مدلسازی پخش ذرات معلق کارخانه سیمان کرمان با استفاده از دینامیک سیالات محاسباتی

Backgrounds and Objectives: The dispersion of particulate matter has been known as the most serious environmental pollution of cement plants. In the present work, dispersion of the particulate matter from stack of Kerman Cement Plant was investigated using Computational Fluid Dynamics (CFD) modeling.Materials and Methods: In order to study the dispersion of particulate matter from the stack, a ...

متن کامل

Multiphase flow and tromp curve simulation of dense medium cyclones using Computational Fluid Dynamics

Dense Medium Cyclone is a high capacity device that is widely used in coal preparation. It is simple in design but the swirling turbulent flow, the presence of medium and coal with different density and size fraction and the presence of the air-core make the flow pattern in DMCs complex. In this article the flow pattern simulation of DMC is performed with computational fluid dynamics and Fluent...

متن کامل

Kinetics analysis of electrophoretic deposition using small signal and large signal modeling, Case study: Nano-Mullite suspension

Having sufficient and accurate understanding about kinetics of phenomena, could be an important reason for further technological progresses. Finding a white-box mathematical model for weight vs. time curves of Electrophoretic Deposition (EPD) using large and small signal analysis has been studied thoroughly in the present investigation. Weight-Time curves of nano-Mullite suspension have been tr...

متن کامل

A Comprehensive Approach to an Optimum Design and Simulation Model of a Mechanical Draft Wet Cooling Tower

The present paper describes the designing of a thermally and economically optimum mechanical draft counter-flow wet cooling tower. The design model allows the use of a variety of packing materials in the cooling tower toward optimizing heat transfer. Once the optimum packing type is chosen, a compact cooling tower with low fan power consumption is modelled within the known design variables....

متن کامل

ذخیره در منابع من


  با ذخیره ی این منبع در منابع من، دسترسی به آن را برای استفاده های بعدی آسان تر کنید

برای دانلود متن کامل این مقاله و بیش از 32 میلیون مقاله دیگر ابتدا ثبت نام کنید

ثبت نام

اگر عضو سایت هستید لطفا وارد حساب کاربری خود شوید

عنوان ژورنال:

دوره   شماره 

صفحات  -

تاریخ انتشار 2004